Arctic Cove EVC351 Manual Del Operador página 13

NOTE: When the pump is on, water will be pumped into
the filter media, which will have a cooling effect on the
air flow.
NOTICE:
Do not operate the evaporative cooler without the filter
media while the pump is running. Doing so could damage
the motor and reduce performance.
 Press the COOL/HUMIDIFY button again to turn the
pump off.
WARNING:
After turning the pump off, run the evaporative cooler
fan for 15 to 30 minutes to dry the filter media. Always
thoroughly dry the filter media to prevent the possible
formation of bacteria or mold. Circulating air through a
filter media that contains bacteria or mold can result in
serious personal injury or illness.
WARNING:
Always empty water container and thoroughly clean with
soap and water when not in use to prevent the possible
formation of bacteria or mold. Using a cooler that
contains bacteria or mold can result in serious personal
injury or illness.
Switching between humidifying and cooling:
 To cool an area, turn the pump on and select
Speed 4 ( ), Speed 3 (
The cool icon ( ) will appear in the digital display.
NOTE: To allow for proper ventilation and optimal
cooling, place the unit in front of an open window and
leave the door to the room slightly open.
 For better cooling, add ice to the evaporative cooler:
• Open the compartment door and place ice in the water
flow control compartment.
NOTE: Do not place ice directly over the water
distribution holes as this may obstruct the flow of water
to the filter media.
• Add ice into the water container.
WARNING:
Make sure the combination of ice and water does not
cause the water level to rise above the max fill line, which
may result in a water spill or leak. Spilled or leaking water
can result in a slippery surface, create a slip and fall
hazard, and cause property damage.
OPERATION
), or Speed 2 ( ) fan speed.
 To switch from cooling to humidifying, change the fan
speed to Speed 1 ( ). The humidify icon ( ) will appear
in the digital display.
NOTE: When using this product as a humidifier, close
room doors and windows to prevent humidified air
from escaping.
 To stop humidifying or cooling, turn the pump off.
To adjust water flow from the pump:
The flow of water from the pump to the filter media can be
controlled by using the water flow control knob. For cooler
air, increase the flow of water. For warmer air, decrease the
flow.
 Turn the pump on as described earlier.
 Open the compartment door.
 Turn the water flow control knob counterclockwise to
increase the flow of water from the pump and clockwise
to decrease it.
 Close the compartment door.
Changing the distribution of air flow:
The distribution of air flow can be adjusted by changing
the position of the fan louvers. To change the direction of
horizontal airflow, adjust the vertical louvers:
 Press the SWING button on the control panel or remote
control to make the vertical louvers move from left to
right automatically. The swing icon ( ) will appear in the
digital display.
 Press the SWING button again to stop louver movement.
To change the direction of vertical airflow, manually adjust
the horizontal louvers.
Setting the timer:
The evaporative cooler can be set to function automatically
for intervals of 30 minutes up to 8 hours. To set the time for
the evaporative cooler:
 Press the TIMER button to cycle through the available
settings.
 The evaporative cooler will run until the allotted time has
expired.
LOW WATER ALERTS
As the evaporative cooler's pump is running, the amount of
water in the water container will dissipate. When the water
level becomes low, the low water alert will beep and the low
water icon ( ) will flash in the digital display. If the water
supply becomes insufficient to operate the pump, the pump
will shut off automatically. The fan will continue to operate
even when the pump is off.
To resolve the low water alert, disconnect the evaporative
cooler from the power supply and fill the water container as
described earlier. Then restart the unit and resume normal
operation.
9 — English