Axxess CHTO-013 Manual Del Usuario
  1. Manuales
  2. Marcas
  3. Axxess Manuales
  4. Amplificadores de Coches
  5. CHTO-013
  6. Manual del usuario
Axxess CHTO-013 Manual Del Usuario

Axxess CHTO-013 Manual Del Usuario

Ocultar thumbs Ver también para CHTO-013:
1
2
3
4
5
6
7
8
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Descargar este manual
INSTALLATION INSTRUCTIONS FOR PART CHTO-013
Chrysler vehicles
KIT FEATURES
• Provides accessory (12-volt 10 amp)
• Retains R.A.P. (retained accessory power)
• Used in amplified, non-amplified systems, or digital amplified systems
• Provides NAV outputs (parking brake, reverse, and V.S.S.)
• ASWC-1 harness included (ASWC-1 sold separately)
• Adjustable gain control for overall volume (on amplified systems)
• Retains blind spot detection system (if equipped)
• High level speaker input
• Micro "B" USB updatable
• Retains balance and fade
METRA. The World's best kits.™
CHTO-013
2004-up
APPLICATIONS
See inside front cover
1-800-221-0932
INTERFACE COMPONENTS
• CHTO-013 Interface • 16-pin harness with
stripped leads • 10-pin harness to 22-pin Chrysler
harness with stripped leads (A) • 10-pin harness to
22-pin Chrysler harness with stripped leads (B) •
4-pin harness with stripped leads
TOOLS REQUIRED
• Cutting tool • Tape • Crimping tool • Connectors
(example: butt-connectors, bell caps, etc.)
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
metraonline.com
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION

Publicidad

Tabla de contenido
loading

Manuales relacionados para Axxess CHTO-013

Resumen de contenidos para Axxess CHTO-013

  • Página 1 INSTALLATION INSTRUCTIONS FOR PART CHTO-013 CHTO-013 INTERFACE COMPONENTS • CHTO-013 Interface • 16-pin harness with Chrysler vehicles stripped leads • 10-pin harness to 22-pin Chrysler harness with stripped leads (A) • 10-pin harness to 2004-up 22-pin Chrysler harness with stripped leads (B) • 4-pin harness with stripped leads APPLICATIONS See inside front cover TOOLS REQUIRED KIT FEATURES • Cutting tool • Tape • Crimping tool • Connectors (example: butt-connectors, bell caps, etc.) • Provides accessory (12-volt 10 amp) • Retains R.A.P. (retained accessory power) • Used in amplified, non-amplified systems, or digital amplified systems • Provides NAV outputs (parking brake, reverse, and V.S.S.) • ASWC-1 harness included (ASWC-1 sold separately) CAUTION: Metra recommends disconnecting the • Adjustable gain control for overall volume (on amplified systems)

  • Página 2: Connections To Be Made

    CHTO-013 Applications Connections to be made From the 16-pin harness HaRnESS (a) - LD-CHTO-31 CHRYSLER DODGE JEEP • Connect the (2) Red wires to the ignition/accessory wire of the aftermarket radio. (continued) (continued) 300 2005-2007 Magnum 2005-2007 Grand Cherokee • Connect the Orange/White wire to the illumination wire of the aftermarket Ram 1500 2006-2008 2005-2007 Aspen 2007 radio. If the aftermarket radio does not have an illumination wire, tape off the DODGE Ram 2500/3500 Patriot 2007-2008 Orange/White wire. Caliber...
  • Página 3 CHTO-013 Connections to be made • Connect the Gray wire to the right front positive speaker output of the • Connect the Green wire to the radio’s left rear positive speaker output. aftermarket radio. • Connect the Green/Black wire to the radio’s left rear negative speaker output. • Connect the Gray/Black wire to the right front negative speaker output of the • Connect the Purple wire to the radio’s right rear positive speaker output. aftermarket radio. • Connect the Purple/Black wire to the radio’s right rear negative • Connect the Green wire to the radio’s left rear positive speaker output. speaker output. • Connect the Green/Black wire to the radio’s left rear negative speaker output. Tip: If you are unsure if your vehicle is amplified or not, note that these following • Connect the Purple wire to the radio’s right rear positive speaker output.

  • Página 4: Important Warning

    INSTALLATION INSTRUCTIONS FOR PART CHTO-013 Installing the CHTO-013 • With all connections completed to the aftermarket radio, plug the 22-pin harness into the vehicles wiring harness. • Reconnect the negative battery terminal. • Cycle the key, by turning the ignition on for 30 seconds. Then off and on again to test the radio. Testing the CHTO-013 • Turn the ignition on if not already, and then turn the radio on to verify that the radio works. Check balance and fader controls for proper operation. For amplified models only: • To adjust the overall volume of your audio system rotate the potentiometer, which is located on the 16-pin side of the interface clockwise. NOWLEDGE IS OWER Enhance your installation and fabrication skills by IMPORTanT WaRnInG enrolling in the most recognized and respected mobile electronics school in our industry.

  • Página 5: Vehículos Chrysler 2004 Y Mas

    INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA CHTO-013 CHTO-013 COmPOnEnTES DE LA InTERfASE • Interfase CHTO-013 • Arnés de 16 pins con Vehículos Chrysler conectores pelados • Arnés de 10 pins a arnés Chrysler de 22 pins con conectores pelados (A) 2004 y mas •...

  • Página 6: Conexiones Que Se Deben Hacer

    CHTO-013 Aplicaciones Conexiones que se deben hacer Desde el arnés de 16 pins HaRnESS (a) - LD-CHTO-31 • Conecte los (2) cables rojos al cable de ignición/accesorio del radio de CHRYSLER DODGE JEEP (seguido) (seguido) mercado secundario. 2005-2007 Magnum 2005-2007...
  • Página 7 CHTO-013 Conexiones que se deben hacer • Conecte el cable gris con la salida positiva de la bocina frontal derecha del • Conecte el cable verde con la salida de la bocina positiva izquierda de atrás radio de mercado secundario del radio.

  • Página 8: Instalación Del Chto-013

    INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA CHTO-013 Instalación del CHTO-013 • Cuando termine de hacer todas las conexiones en el radio de mercado secundario, conecte el arnés de 22 pins en el arnés de cables del vehículo. • Reconecte la terminal de la batería negativa.

Tabla de contenido