Tabla de contenido
Publicidad
Enlaces rápidos
38
50
Sensor Eye
Adjustment Screw
9, 14, 43
Fig. 1
HTV8EE*1C
MANUAL DEL PROPIETARIO HALSEY TAYLOR
MANUEL DE L'UTILISATION HALSEY TAYLOR
™
HTVEE
Series Barrier-Free Water Coolers
™
HTVEE
La Barrera de la serie Liberta Agua Coolers
™
HTVEE
Coolers d'Eau de Barrière-Libère de feuilleton
33
25
21
27
37
41
11
13
29
HTV8EE*2C
OWNERS MANUAL
26
12
39
46
15, 49
2, 3, 5
Page 1
30
22
17
50
42
16
37
8, 45
7
6
40
20
98494C (Rev. A - 3/09)
Publicidad
Tabla de contenido
Manuales relacionados para Halsey Taylor HTVEE Serie
Resumen de contenidos para Halsey Taylor HTVEE Serie
- Página 1 HTV8EE*1C HTV8EE*2C OWNERS MANUAL MANUAL DEL PROPIETARIO HALSEY TAYLOR MANUEL DE L’UTILISATION HALSEY TAYLOR ™ HTVEE Series Barrier-Free Water Coolers ™ HTVEE La Barrera de la serie Liberta Agua Coolers ™ HTVEE Coolers d’Eau de Barrière-Libère de feuilleton Sensor Eye...
- Página 2 HTV8EE*1C HTV8EE*2C Fig. 2 98494C (Rev. A - 3/09) Page 2...
-
Página 3: Limpieza
HTV8EE*1C HTV8EE*2C HANGER BRACKET & TRAP INSTALLATION El PARENTESIS del GANCHO & LE CROCHET DE CINTRE & 1) Remove the hanger bracket fastened to back of the la INSTALACION de la TRAMPA L’INSTALLATION DE PIEGE cooler by removing one (1) screw. 1) Quita gancho paréntesis abrochó... -
Página 4: Cleaning The Strainer
HTV8EE*1C HTV8EE*2C Top Cover Removal Please remove bottom cover before removing top cover. To remove top cover (Item 34), use a small Fig. 4 screwdriver to release the snap for the top cover as shown in Fig. 4. Then pull the small tabs on each side of the top cover outward slightly and slide upward to remove. - Página 5 HTV8EE*1C HTV8EE*2C Removing the basin To remove the basin (Item 32), remove two screws (Item 22) on top of the basin (Shown in Fig. 6). Then remove the four screws (Item 48) located underneath the dispenser bottom (Item 36). Finally pull polytube (Item 17) out of bubbler (Item 16) as shown in Fig.
- Página 6 HTV8EE*1C HTV8EE*2C Fig. 9 12, 18, 19 Bottom Cover Removal To access the refrigeration system and plumbing connections, remove two screws (Item 49) to remove bottom cover (Item 35). See Fig. 9. Tapa Inferior La eliminación Para accesar al sistema de refrigeración y las conexiones de empalmes, desmonte los dos tornillos (Articulo 49) para retirar la tapa inferior (Articulo 35).
-
Página 7: Sensor Control
HTV8EE*1C HTV8EE*2C SENSOR RANGE ADJUSTMENT: The electronic sensor used in this cooler is factory pre-set for a “visual” range of 36 inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment procedure below: Using a small tip screwdriver, locate range adjustment screw through the small hole between the sensor lenses (See Page 1.) Turn this screw clockwise to increase range and counterclockwise to decrease range (See Fig. -
Página 8: Descripción
HTV8EE*1C HTV8EE*2C Fig. 10 SENSOR SOLENOID VALVE OVERLOAD COMPRESSOR COLD CONTROL MALE TERMINAL ON WHITE SHORT LEAD ON POWERCORD RELAY WIRING DIAGRAM - HTV8EE 115V El ESQUEMA que ALAMBRA - HTV8EE 115V DIAGRAMME qui TELEGRAPHIE - HTV8EE 115V 220V PARTS LIST/ 220V LISTA DE PIEZAS/ 220V LISTE DES PIÈCES ITEM NO. - Página 9 HTV8EE*1C HTV8EE*2C PARTS LIST/ LISTA DE PIEZAS/ LISTE DES PIÈCES DESCRIPTION DESCRIPCIÓN DESCRIPTION ITEM NO. PART NO. 100322740560 Gasket - Bubbler (upper and lower) Obturador - Borboteador (Superior e inferior) Joint statique - barboteur (supérieur et inférieur) 100806740570 Grommet - Compressor Mtg. Arandela Aislante-Mtg del Compresor Oeillet - surpresseur 101516143550...