Personal Protective Equipment; Functional Description - Hilti TE 2-A Manual De Instrucciones

Take the influences of the surrounding area into account.
G
Do not expose the tool to rain or snow and do not use
it in damp or wet conditions.
Keep the grips dry, clean and free from oil and grease.
G
The tool may be used hand-held only.
G
Always hold the tool with both hands on the grips pro-
G
en
vided.
Switch the tool on only after bringing it into position
G
at the workpiece.
Observe instructions on care and maintenance and on
G
changing insert tools.
Do not insert wires or other similar objects into the
G
ventilation slots or other openings.
3.2.1 Mechanical hazards
Follow the instructions concerning care and maintenance.
G
Check that the insert tools used are compatible with
G
the chuck system and that they are secured in the chuck
or gear housing correctly.
3.2.2 Electrical hazards
Protect yourself against electric shock. Avoid body
G
contact with earthed / grounded objects, e.g. pipes,
radiators, cookers and fridges.
Damaged switches must be replaced at a Hilti service
G
center. Do not use the tool if it cannot be switched off
and on properly.
The tool may be repaired by trained electrical specialists
G
only (Hilti service) using original Hilti spare parts. Fail-
ure to observe this point may present considerable risk
to the user.
Ensure that the outer surface of the battery is clean
G
and dry before inserting the battery in the appropri-
ate charger for charging.
Check that the battery is securely attached to the tool.
G
A falling battery could injure you or other persons.
Batteries that have reached the end of their life must
G
be disposed of safely.

4. Functional description

The TE 2-A is a cordless rotary hammer for profession-
al use. Its ergonomically designed rubber-padded grip
reduces fatigue and provides a secure hold.
The items supplied include:
- The electric tool
- B24/2.0 NiCd, B24/2.4 NiCd or B24/3.0 NiMH battery
- C 7/24 or C 7/36-ACS charger
- Operating instructions
- Toolbox or cardboard box
4
Printed: 07.07.2013 | Doc-Nr: PUB / 5070812 / 000 / 00
3.2.3 Thermal hazards
The insert tool may become hot during use. You should
G
therefore wear protective gloves when changing insert
tools.
3.2.4 Liquids
A caustic liquid may leak from defective batteries. Avoid
G
contact with this liquid. In the event of contact with the
skin, wash the area affected with soap and plenty of
water. Should the liquid come into contact with the
eyes, flush the eyes with water immediately and sub-
sequently consult a doctor.
3.3 Requirements to be met by users
The tool is intended for professional use.
G
The tool may be operated, serviced and repaired only
G
by authorized, trained personnel. This personnel must
be informed of any special hazards that may be encoun-
tered.

3.4 Personal protective equipment

The operator and other persons in the immediate vicin-
G
ity must always wear eye protection, ear protection
and breathing protection while the tool is in use.
Wear Wear
eye ear
protection protection
3.5 Symbols used on the tool
V = volts
–––
= direct current
- - -
n = no load speed
o
min –1 = revolutions per minute
4.1 Use of the tool as directed
The TE 2-A is a hand-held cordless rotary hammer for
driving and removing screws, drilling in steel, wood and
masonry and hammer drilling in concrete and mason-
ry. It is intended for use on construction sites of all kinds
for general construction, interior finishing, conversion
and renovation work.
The tool is designed for continuous use.
G
The tool may be used only in a dry environment.
G
Wear Wear
breathing protective
protection gloves
= hammer drilling
= rotation only
∅
= diameter