Instructions For The Installer; Building In; Suitable Location; Electrical Connection (For U.k. Only) - Hoover HF7 Manual De Instrucciones

1. INSTRUCTIONS FOR THE INSTALLER

INSTALLING A DOMESTIC APPLIANCE CAN BE A COMPLICATED OPERATION WHICH IF NOT CARRIED OUT CORRECTLY, CAN SERIOUSLY
AFFECT CONSUMER SAFETY. IT IS FOR THIS REASON THAT THE TASK SHOULD BE UNDERTAKEN BY A PROFESSIONALLY QUALIFIED
PERSON WHO WILL CARRY IT OUT IN ACCORDANCE WITH THE TECHNICAL REGULATIONS IN FORCE. IN THE EVENT THAT THIS ADVICE IS
IGNORED AND THE INSTALLATION IS CARRIED OUT BY AN UNQUALIFIED PERSON, THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR ANY TECHNICAL FAILURE OF THE PRODUCT WHETHER OR NOT IT RESULTS IN DAMAGE TO GOODS OR INJURY TO INDIVIDUALS.
1.1.B UILDING IN
The hob may be installed in any work top which is he at resistant to a
temperature of 100°C, and has a thickness of 25-45 mm. The
dimensions of the insert to be cut out of the work top are in shown in.
Figure 1.
If the Hob is fitted next to a cabinet o neither side, the distance
between the hob and the cabinet must be at least 15 cm; while the
distance between the hob and the rear wall must be at least 5,5 cm
(Figure 2).
The distance between the hob and any other unit or appliance above
it (e.g. An extractor hood) must be no less than 70 cm. When there is
an accessible space between the built-in hob and the cavity below, a
dividing wall made of insulating material should be inserted (wood or
a similar material). Figure 3
A watertight seal is supplied with the hob
Warning: it is not allowed to install a hob above an oven.

1.2. SUITABLE LOCATION

This appliance must be installed in accordance with applicable
regulations and should only be used in well-ventilated locations.
Before using this appliance carefully study the instruction book.
A gas-powered cooking appliance produces heat and humidity in the
area in which it is installed. For this reason you should ensure good
ventilation either by keeping all natural air passages open or by
installing an extractor hood with an exhaust flue. Intensive and
prolonged use of the appliance may require extra ventilation, such as
the opening of a window or an increase in speed of the electric fan, if
you have one.
If a hood can not be installed, an electric fan should be fitted to an
outside wall or window as long there are air vents in the area.
The electric fan should be able to carry out a complete change of air in
the kitchen 3-5 times every hour. The installer should follow the
relevant national standards.

2. ELECTRICAL CONNECTION (FOR U.K. ONLY)

Warning this appliance must be earthed
This appliance is designed for domestic use only. Connection to the
main supply must be made by a competent electrician, ensuring that
all current regulations concerning such installations are observed.
The appliance must only be connected to a suitably rated spur point, a
3 pin 13 amp plug/socket is not suitable. A double pole switch must be
provided and the circuit must have appropriate fuse protection.
Further details of the power requirement of the individual product will
be found in the Table B and on the appliance rating plate. You are
advised, should you wish to use a longer cable than the one supplied,
that a suitably rated heat resistant type must be used.
The wiring must be connected to the mains supply as follows:
CONNECT
Green & Yellow Wire
Blue Wire
Brown Wire
Note: We do not advocate the use of earth leakage devices with
electric cooking appliances installed to spur points because of the
«nuisance tripping » which may occur. You are again reminded that the
appliance must be correctly earthed, the manufacturer declines any
responsibility for any event occurring as a result of incorrect electrical
installation.
TO SPUR TERMINAL
Earth Connection
Neutral Connection
Live Connection

2.1. ELECTRICAL CONNECTION

Check the data on the rating plate, located on the out side of the unit, to
ensure that the supply and input voltage are suitable.
Before connection, check the earthing system.
By Law, this appliance must be earthed. If this regulation is not
complied with, the Manufacturer will not be responsible for any
damage caused to persons or property. If a plug is not already
attached, fit a plug appropriate to the load indicated on the rating plate.
The earth wire is coloured yellow/green. The plug should always be
accessible.
Where the hob is connected direct to the electricity supply, a circuit
breaker must be fitted.
If the power supply cord is damaged this is to be replaced by a qualified
engineer so as to prevent any potential risk.
When replacing the cable, you should use a cable of the same features
as the original
The earth wire (green and yellow coloured) must be at least 10 mm
longer than the live and neutral wires.
LIVE
MainsSupply
EARTH
NEUTRAL

2.2. GAS CONNECTION

These instructions are for qualified personnel, installation of
equipment must be in line with the relevant national standard.
(For U.K. only: by law the gas installation\commissioning must
be carried out by a "Gas Safe" installer)
All work must be carried out with the electricity supply disconnected.
The rating plate on the hob shows the type of gas with which it is
designed to be used. Connection to the mains gas supply or gas
cylinder should be carried out after having checked that it is regulated
for the type of gas with which it will be supplied.
Use only pipes, washers and sealing washers which comply with
the relevant national standards.
For some models a conic link is furnished to outfit for the
installation in the countries where this type of link is obligatory; in
Figure 5 it is pointed out how to recognize the different types of
links (CY = cylindrical, CO = conic). In every case the cylindrical
part of the link has to be connected to the hob.
When connecting the hob to the gas supply via use of flexible
hoses please ensure that the maximum distance covered by the
hose does not exceed 2 metres.
To prevent any potential damage to the hob please carry out the
installation following this sequence (Figure 4):
1) As illustrated, assemble parts in sequence:
A: 1/2Male Adaptor Cylindirical,
B:1/2Seal ,
C:1/2Female Gas Adaptor Conical-Cylindirical or Cylindirical-
Cylindirical
2) Tighten the joints with the spanner, remembering to place
the pipes into position.
3) Attach fitting C to mains gas supply using rigid copper
pipe or flexible steel pipe.
IMPORTANT: carry out a final check for leaks on the pipe
connections using a soapy solution. NEVER USE A FLAME.
Also, make sure that the flexible pipe cannot come into
contact with a moving part of the cabinet (eg, adrawer) and
that it is not situated where it could be damaged.
Warning: If gas can be smelt in the vicinity of this appliance turn
off the gas supply to the appliance and call the engineer directly.
Do not search for a leak with a naked flame.
06 GB - IE
BrownWire
L
Green/YellowWire
PowerCable
BlueWire
N