Onkyo DP-S1A Manual De Instrucciones página 59

> Before Start > Part Names
regular single-ended operation, however.
0 This unit does not support simultaneous use of the balanced headphone jack and the
headphone jack. Using both jacks at the same time may result in damage.
∫ Line Out Mode
"On": Switch the headphone output to the line output mode to connect external equipment.
When "Line Out Mode" is on, output through the headphone jack is at maximum volume, so
do not use headphones. Adjust the volume on the connected device.
0 When turned on for European models, you can then select either "Fixed (default value)"
or "Variable". When "Variable" is selected, volume can be adjusted on this unit. If you
select "Fixed", adjust the volume on the connected external device.
"Off (default value)": Line output is not enabled
∫ Audio
Gain: You can select the headphone output level to suit your headphones.
Select "High (default value)", "Normal", or "Low".
0 Lower the volume first if you intend to select "High".
0 When connecting a pair of headphones for the first time, set to "Low" and change the
volume level gradually.
Volume Limiter: You can set an upper limit for the maximum volume so that the volume
does not increase too much. Select between "0" and "60 (default value)".
USB Audio: DSD format music files can be output in DoP format via USB. Note that DSD is
not output if "Output DSD" is set to off.
0 If the attached USB-DAC does not support DoP stream, playback and attached devices
may be adversely affected.
Output DSD: "On" / "Off (default value)"
ReplayGain
When this is on, the variation in volume between each music file is corrected and played
according to a standard value. To use ReplayGain, you first need to use software, etc., on a
computer to embed the volume information in the music file.
Enable ReplayGain: "On" / "Off (default value)"
Normalize setting: Select either "Track Gain" or "Album Gain" to use to make the volume
uniform.
"Track Gain (default value)" / "Album Gain"
Preamp with RG info: When the music file has ReplayGain information, the volume level is
22
> Initial Setup > Playback
Advanced Setup
either increased or decreased according to the standard value. The volume level can be set
in 25 steps between "-12 dB" and "12 dB". ("6 dB" is the default value)
Preamp without RG info: When the music file does not have ReplayGain information, the
volume level is either increased or decreased according to the standard value. The volume
level can be set in 13 steps between "-12 dB" and "0 dB". ("0 dB" is the default value)
∫ Music Library Sync
Auto sync: When this is on, music files you have copied to this unit from a computer or
music files on a micro SD card are automatically synchronized with the library.
"On (default value)": When this function is to be used
"Off": When this function is not to be used
Sync Now
If "Auto sync" is off, tap this to manually synchronize the music files with the library. You can
select "Sync All" or "Sync Added Songs" after tapping this.
Sync All: Select to synchronize all transferred tracks.
Sync Added Songs: Select to synchronize only tracks that have been added.
∫ SD Card
Unmount SD Card: You can unmount a micro SD card. The card can be damaged or may
stop working properly if you fail to unmount the card first.
Format SD Card: You can initialize a micro SD card. All the data on the card will be deleted
when you initialize it, so make sure you save data you want to keep to a computer, etc. To
initialize, after tapping the micro SD card to be initialized, tap "Format" - "Confirm".
∫ Physical Buttons
Volume Rotation: You can set the direction to turn the dial when adjusting the volume.
Normal (default value): Turn clockwise to increase the volume.
Reverse: Turn anticlockwise to increase the volume.
Operations while Holding
When set to "Enable", even when you slide the hold switch (P5) up to lock operations on this
unit, the Volume dial and side buttons for play (P5), etc., can still be used. Tap this to change
the settings for "Volume" and "Side Buttons".
Volume: "Disable (default value)" / "Enable"
Side Buttons: "Disable (default value)" / "Enable"
| Supplementary Information | Others