Important Safety Instructions - Hamilton Beach Tempest Serie Manual De Operación

IMPORTANT SAFETY INSTRUCTIONS

WARNING –
When using electrical appliances, basic safety precautions should be followed,
including the following:
• Read the Operation Manual before using blender.
Keep Operation Manual handy.
• Before first use, wash container assembly in hot,
soapy water. Do NOT place in dishwasher.
• Plug into a grounded outlet.
• Do not remove ground.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before cleaning or servicing.
• To reduce risk of personal injury, unplug cord from
outlet when not in use, and before putting on or
taking off parts.
• Unplug the blender and inspect the power cord
insulation for cracks on a weekly basis. Refer to
"Technical Service" for repair or replacement.
• To protect against electrical shock, do not immerse
cord, plug, or blender base in water or any other
liquid.
• Do not spray the base with a high-pressure spray
gun.
• Extreme caution must be used when moving an
appliance containing hot oil or other hot liquids.
• Do not use appliance for other than intended use.
• Not intended for use by or near children.
• Children should be supervised to ensure they do not
play with the appliance.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory,
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
• The use of accessory attachments not
recommended by the appliance manufacturer may
cause injuries.
• To reduce risk of personal injury and to prevent
damage to blender or container and cutter assembly,
DO NOT insert utensils into blender container while
operating blender.
• Do not store any kitchen utensils in the container
because the blender would be damaged if
inadvertently turned on.
• To prevent possibility of serious personal injury,
keep hands out of blender container while operating
blender. Always operate blender with container cover
in place.
• Avoid contacting moving parts. Switch off the
appliance and disconnect from power supply before
changing accessories or approaching parts that
move in use.
• Blades are sharp. Handle carefully.
• If cutter assembly blades are loose, discontinue use
immediately and replace cutter assembly. Do not
attempt to repair or tighten cutter assembly.
2
SAVE THESE IN STRUC TIONS
–
GB
• Inspect container and cutter assembly daily. Do not
use broken, chipped, or cracked container. Check
cutter for wear, nicks, or broken blades. Do not use
broken, loose, or cracked cutting blades.
• Do not use outdoors.
• This appliance is intended for short periods of
operation, with a rated operating time of 3 minutes.
• Do not leave blender unattended while it is
operating.
• To prevent damage to blender, container, or cutter
assembly, DO NOT move or shake blender while in
operation. If blending action stops during operation,
turn blender OFF ( ), remove container from base,
remove container cover, and use a thin rubber
spatula to push mixture towards cutters.
• When blending hot liquids, remove center-piece of
two-piece lid. Hot liquids may push lid off jar during
blending. To prevent possible burns: Do not fill
blender jar beyond the 1 quart (1 liter) level. With the
protection of an oven mitt or thick towel, place one
hand on top of lid. Keep exposed skin away from lid.
Start blending at lowest speed.
• The blender is provided with a power switch/circuit
breaker on the bottom of the unit. If the motor stops
turning, reset the power switch.
• This blender is designed with motor overload
protection. If the motor stops during operation due
to overheating, unplug the unit and allow it to cool
down for 15 minutes. Plug unit back after 15 minutes
to resume normal operation.
• The normal function of this product may be
disturbed by strong electromagnetic interference.
If this occurs, simply reset the product and resume
normal operation by following the operation manual.
If normal operation cannot be resumed, place the
product in a different location.
• Do not operate any appliance with a damaged
cord or plug or after the appliance malfunctions,
or is dropped or damaged in any manner. Refer to
"Technical Service" for instructions on examination,
repair, or electrical or mechanical adjustment.
• If the supply cord of this appliance is damaged,
it must be replaced by the manufacturer or its
service agent or a similar qualified person.
UK ONLY: If fitted with a non-rewirable U.K.
plug, the 13 amp fuse approved by ASTA
to be B.S. 1362 must be used. If you nee
a replacement fuse carrier, it must be replaced
with the same colour coded carrier with the same
markings. Fuse covers and carriers can be obtained
from approved service agents.
• Always operate blender with lid in place. Remove
emulsion cup only for adding ingredients or to insert
the tamper.
Caution: Do not operate without cover in place.
d
–