General Information; Unpacking; Accessory Box; Assembly - Generac GP Serie Manual Del Propietário

General Information

1.1 UNPACKING

• Remove all packaging material.
• Remove separate accessory box.
• Remove the generator from carton.

1.1.1 ACCESSORY BOX

Check all contents. If any parts are missing or damaged, locate an
authorized dealer at 1-888-436-3722.
• 1 - Owner's Manual
• 1 - Liter Oil SAE 30
• 2 - Never-Flat Wheels
• 1 - Hardware Bag (containing the following):
• 2-Rubber Feet
• 2-1/2" Axle Pins
• 2-Cotter Pins
• 2-1/2" Flat Washers
• 2-Short Bolts
• 2-Flange Nuts (electric start only)

1.2 ASSEMBLY

The generator requires some assembly prior to using it. If problems
arise when assembling the generator, please call the Generator
Helpline at 1-888-77LOWES.

1.2.1 ASSEMBLING THE ACCESSORY KIT

The wheels are designed into the unit to greatly improve the
portability of the generator.
You will need the following tools to properly install the accessory
kit.
• Needle Nose Pliers
• Ratchet and a 13mm (1/2") socket
• 13mm (1/2") box wrench
The wheels are not intended for over-the-road use.
1. Refer to Figure 1 and install the Wheels as follows:
• Slide the Axle Pins through the Wheel, 1/2" Flat Washer, and Wheel
Bracket on the frame.
• Insert the Cotter Pin through the Axle Pin then bend the tabs (of the
Cotter Pins) outward to lock into place.
2. Refer to Figure 1 and install the Frame Foot and Rubber
Bumpers as shown.
• Slide the Rubber Bumper studs through the Frame Foot then install
the Locking Flange Nuts.
• Slide the Hex Head Bolts through the holes in the Frame Rail.
• Slide the Frame Foot onto the Hex Head Bolts then install the
Locking Flange Nuts.
3. Refer to Figure 1 and install the Handle as shown.
• Slide the long Bolts through the Handle Bracket and Handle, then
install the Hex Nuts.
4
• 1 - Handle Assembly
• 1 - Frame Foot
• 1 - Battery Charger (electric
start only)
• 2-M8 Bolt (Long)
• 2-M8 Bolts (Short)
• 2-M8 Acorn Nut
• 4-Hex Flanged M8 Nuts
• 2-Lock Washers
NOTE:
Figure 1 – Wheel & Handle Assembly
1.2.2 BATTERY CABLE CONNECTION (ELECTRIC START
ONLY)
The unit has been deliberately shipped with the battery cables
disconnected.
To connect the battery (see Figure 13 for connection details):
1. Cut off cable ties securing battery cables and remove red
covers from battery terminals.
2. First, connect the red cable to the positive (+) battery terminal
with the bolt, lock washer and nut supplied.
3. Connect the black cable to the negative (-) battery terminal
with the bolt, lock washer and nut supplied.
4. Make sure all connections are secure. Slide the rubber boots
over the terminals and connection hardware.
If the battery is unable to start the engine, charge it with the
12V charger included in the accessory box (see the "Charging a
Battery" section for details).

2.1 KNOW THE GENERATOR

Read the Owner's Manual and Safety Rules before operating
this generator.
Compare the generator to Figures 2 through 4 to become
familiarized with the locations of various controls and adjustments.
Save this manual for future reference.
1. 120 Volt AC, 20 Amp, Duplex Receptacle – Supplies electrical
power for the operation of 120 Volt AC, 20 Amp, single-phase,
60 Hz electrical lighting, appliance, tool and motor loads.
2. 120/240 Volt AC, 30 Amp Locking Receptacle – Supplies
electrical power for the operation of 120 and/or 240 Volt AC,
30 Amp, single-phase, 60 Hz, electrical lighting, appliance,
tool and motor loads.
3. Circuit Breakers (AC) – Each receptacle is provided with a
push-to-reset circuit breaker to protect the generator against
electrical overload.
4. Oil Drain – Use to drain engine oil.
5. Air Filter – Filters intake air as it is drawn into the engine.
NOTE: