Sunoptic Surgical TITAN 9000-II Manual De Operación página 4

3. ASSEMBLING THE HEADLIGHT SYSTEM 3. ASSEMBLING THE HEADLIGHT SYSTEM
Before continuing remove the protective lens cap. Before continuing remove the protective lens cap.
Insert a fully charged encrypted battery into the Battery Holster and ensure it is fully seated Insert a fully charged encrypted battery into the Battery Holster and ensure it is fully seated Insert a fully charged encrypted battery into the Battery Holster and ensure it is fully seated
down on the connector at the bottom of the battery cavity. down on the connector at the bottom of the battery cavity.
Should a non-encrypted battery be installed, two encrypted battery be installed, two beeps will be heard upon insertion
indicating that an incorrect battery is being used and the unit will not power up. Insert and indicating that an incorrect battery is being used and the unit will not power up. Insert and indicating that an incorrect battery is being used and the unit will not power up. Insert and
encrypted battery and the unit will power up. encrypted battery and the unit will power up.
To attach the power cable from the LED Module to the Battery Holster, insert the push-pull To attach the power cable from the LED Module to the Battery Holster, insert the push To attach the power cable from the LED Module to the Battery Holster, insert the push
quick connector of the LED Module into the receptacle on the lead from the Battery Holster quick connector of the LED Module into the receptacle on the lead from the Battery Holster quick connector of the LED Module into the receptacle on the lead from the Battery Holster
until it clicks in place as shown here. This connection will not come off when positively until it clicks in place as shown here. This connection will not come off
engaged. You can rotate the connectors to find the keyway and then press together and engaged. You can rotate the connectors to find the keyway and then press together and engaged. You can rotate the connectors to find the keyway and then press together and
not damage the pins.
The On/Off switch is also the LED intensity control. Simply rotate the knob clockwise or The On/Off switch is also the LED intensity control. Simply rotate the knob clockwise or The On/Off switch is also the LED intensity control. Simply rotate the knob clockwise or
counter-clockwise to produce the desired clockwise to produce the desired light output.
The headlight has an iris to allow adjustment of the beam spot diameter. Rotate the fluted has an iris to allow adjustment of the beam spot diameter. Rotate the fluted has an iris to allow adjustment of the beam spot diameter. Rotate the fluted
iris adjustment ring on the headlight clockwise or counterclockwise for the appropriate spot iris adjustment ring on the headlight clockwise or counterclockwise for the appropriate spot iris adjustment ring on the headlight clockwise or counterclockwise for the appropriate spot
diameter.
The battery holster is worn on a belt; on the The battery holster is worn on a belt; on the rear side of the holster is a metal belt clip that
slips over and secures to a belt. The power cable secures into the cable clips on the side slips over and secures to a belt. The power cable secures into the cable clips on the side slips over and secures to a belt. The power cable secures into the cable clips on the side
and rear of the headband.
To remove the LED Module from the Battery Holster, press the small raised button on the To remove the LED Module from the Battery Holster, press the small raised button on the To remove the LED Module from the Battery Holster, press the small raised button on the
quick disconnect device located between the LED Module and the Battery Holster and pull quick disconnect device located between the LED Module and the Battery Holster and pull quick disconnect device located between the LED Module and the Battery Holster and pull
straight out without twisting. straight out without twisting.
Next, place the headband on your head; you can Next, place the headband on your head; you can make size adjustments by turning the
knob on the rear of the headband until it feels comfortable. For more comfort you can knob on the rear of the headband until it feels comfortable. For more comfort you can knob on the rear of the headband until it feels comfortable. For more comfort you can
adjust the cross band.
LIT-224
SUNOPTIC SURGICAL SUNOPTIC SURGICAL
(English) (English)
rear side of the holster is a metal belt clip that
make size adjustments by turning the
®
beeps will be heard upon insertion
when positively
Date o Date of Revision: f Revision:10/04/17
Rev. -
Page 4 of 50