Intended Use - Craftsman CMCCS660 Manual De Instructiones

the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 °C – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger
using a cloth or soft non-metallic brush. Do not use
water or any cleaning solutions.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)

Intended Use

This chain saw is designed for pruning applications
and cutting logs up to 14" (355 mm) in diameter.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Installing the Guide Bar and Saw Chain
(Fig. A, B–D)

CAUTION: Sharp chain. Always wear protective
gloves when handling the chain. The chain is sharp
and can cut you when it is not running.

WARNING: Sharp moving chain. To prevent
accidental operation, ensure that battery is removed
from the tool before performing the following
operations. Failure to do this could result in serious
personal injury.
If the saw chain and guide bar
5
in the carton, the chain has to be attached to the bar, and
both must be attached to the body of the tool.
1. Place the saw on a flat, firm surface.
2. Flip up locking lever and rotate the bar adjust locking
knob 8 counterclockwise as shown in Figure B to
remove sprocket cover 6
3. Wearing protective gloves, grasp the saw chain
wrap it around the guide bar
facing the correct direction.
4. Ensure the chain is properly set in the slot around the
entire guide bar.
5. Place the saw chain around the sprocket
lining up the slot on the guide bar with chain tensioning
pin , and the bolt
18 19
6. Once in place, hold the bar still, replace sprocket
cover 6 . Make sure tool-free tension assembly bolt
hole on the cover lines up with the bolt
main housing. Flip up locking lever and rotate the bar
adjust locking knob 8 clockwise until it clicks, then
loosen knob one full turn, so that the saw chain can be
properly tensioned.
7. Rotate the chain tensioning knob
increase tension as shown in Figure D. Make sure the
saw chain 5 is snug around the guide bar
the bar adjust locking knob until it clicks. The bar is
secure after three audible clicks are heard. Further
tightening is not required.
Fig. B
English
are packed separately
4
.
and
5
, ensuring the teeth are
4
17 . While
, on the base of the tool.
19 , in the
9 clockwise to
4 . Tighten
8
6
9