Haldex EL13050 Guía Del Inicio Rápido página 2

FROM BENDIX
EL1600
EL1300
6.84
Ask These Questions:
1. Are all water ports 1/2" NPT?
2. EL1300 and EL1600 all 1/2"?
3. Will additional lines and fittings be required to relocate
governor?
4. Will additional water lines and fittings be required for
installation?
Optional Installation Choices:
1. Remote mount governor.
2. Remote mount air cleaner.
3. Head can be rotated 180°.
4. The rear end cap can be rotated to allow ease of oil line
hookup.
Installation Materials that Must be
Supplied:
1. If top discharge, supply SN3711J Manifold Kit.
2. If top head clearance is a problem, supply SN371 1K or
SN3711L (low profile) or SN3711AH (side outlet)
Discharge Manifold Kit.
3. Might need 1/2" to 3/8" water port reducers.
Installation Material that Should be
Considered:
1. For ease of installation and extended life of the compressor ,
use the KN17500 Series Flexible Teflon Discharge Line Kit.
2. Let the compressor breathe. Use a KN19040 Heavy-Duty
Filter.
3. Universal Waterline Changeover Kit SN3502 to hookup
coolant lines.
Installation Material that Might be
Required:
1. Remote Mount Governor Kit SN4011B.
12.19
12.00
Compressor Installation
Install the drive hub to the compressor crankshaft. After the
hub is seated, torque the nut to 80 – 100 ft. lbs. plus that
portion of a revolution required to align cotter pin holes. Do
not use the nut to draw down the hub.
Inspect and insure the drive coupling is 2.54 inches long
before reassembly.
Install the compressor to the engine using the supplied gasket.
Care should be taken so no gasket sealant plugs the oil drain.
Assemble the intake manifold, exhaust manifold, and
governor to the compressor using the gaskets provided with
the compressor.
Reconnect the intake, exhaust, oil, and water lines. W ater
must enter the block or head of the compressor and exit the
head at the opposite end.
Close all air and water drain fittings. Fill the engine cooling
system.
Start the engine and check for air, oil, or coolant leakage.
Correct any leakage problems as required.
Check the governor function. Observe the cut-out pressure
(maximum system pressure). Cycle the brakes until the
compressor starts pumping. Observe the system pressure.
The most common pressure range is about 105 psi minimum
system pressure to 125 psi maximum system pressure.
Readjust or replace the governor, if required.
TO HALDEX
.19
10.25
Compressor Illustration
0° Detroit Diesel Compressor
EL13050
EL16050
5
9
8
7
4
B
3
6
2
1
A
15
14
Oil Drain
13
16
Coupling Sleeve (Item 16) can generally be reused. The
coupling sleeve must be 2.54 inches long. If not reusable or
in the correct length, allow enough time to purchase. Reuse
drive hub (Item 13) if not damaged in removal. If reused, the
inside diameter should be no larger than 0.8745 inches. The
hub must be press fit on the compressor crankshaft. Use pipe
plug (Item 12) to plug the option of side or center oil entry .
Item Description
1 Elbow 1/2" ...................................................b
2 Hose Fitting 1/2" Pipe to 1/2" Hose ............b
3 Hose Clamp ................................................b
4 Water Hose 1/2" ID .....................................b
5 Hose-to-Hose Coupling 1/2" .......................b
6 Manifold Gasket N14976 ......................a & c
7 Manifold Lockwashers 35W51020 ..............c
8 Manifold Bolts 08W12028 ...........................c
9 Discharge Manifold 100691C ......................c
10 Discharge Line ............................................d
11 Pipe Plug 1/2" 7 x 107 ................................a
12 Pipe Plug 1/8" 7 x 106 ................................a
13 Drive Hub SN3072BT .................................d
14 Crankshaft Nut 2 x 52 .................................a
15 Cotter Pin 38W10820..................................a
16 Coupling Sleeve 2.54" long SN3072BR......d
A Intake Manifold Mounting Flange
B Governor Mounting Flange
Comment Key:
a – Provided with Compressor c – Part of SN3711K Kit
b – Part of SN3502 Kit d – Order from Haldex
EL13050X
EL16050X
3
10
2
1
11
12
Comment