Haldex EL13040 Instrucciones página 2

FROM BENDIX
Ask These Questions:
1. Is the BW a top head discharge?
2. If BW is a side head discharge, is there clearance for a
top head discharge installation?
3. Are all water ports 1/2" NPT?
4. EL1300 and EL1600 are all 1/2"?
5. Will additional lines and fittings be required to relocate
governor?
6. Will additional water lines and fittings be required for
installation?
7. Is the Cummins "Long" over 11 inches between the
flanges?
8. The EL1300 and EL1600 is 8.50 inches between
flanges?
Optional Installation Choices:
1. Remote mount governor.
2. Remote mount air cleaner.
3. Head can be rotated 180°.
4. Can be naturally aspirated intake or turbocharge intake.
TO HALDEX
Changeover Materials that Must be
Supplied:
1. If top discharge, supply SN3711J Manifold Kit.
2. If top head clearance is a problem, supply SN371 1K or
SN3711L Low Profile Discharge Manifold Kit.
3. Possibly need to 1/2" to 3/8" water port reducers.
4. If replacement is changed to naturally aspirated, supply
plug to plug the turbocharger port on the engine.
5. Must move the fuel pump forward 2 11/16" (difference in
the mounting flange opening) which requires:
• fuel pump pressure lines,
• engine support bracket, and
• adjustment to accelerator rod length.
Changeover Material that Should be
Considered:
1. For ease of changeover and extended life of the
compressor, use the KN17500 Series Flexible Teflon
Discharge Line Kit.
2. Let the compressor breathe. Use a KN19040
Heavy-Duty filter.
3. Universal Waterline Kit SN3502 to hookup coolant lines.
Changeover Material that Might be
Required:
1. Remote Mount Governor Kit SN4011B.
2. Drive gear and drive coupler.
NOTE: Special puller required to remove drive gear .
3. Coupler – compressor to fuel pump.
Compressor Illustration
EL13040
EL16040
Existing
Water Line
7
4
6
1
B
5
3
2
1
A
Existing
Water Line
13
14
15
Oil Drain
12
Change is required in the fuel pump system, throttle linkage,
and engine support bracket. In most changeovers, the old
fuel pump drive coupling (Item 11) can be reused. Haldex
recommends a new coupling be used. Drive Sleeve (Item 15)
can generally be reused if a Bendix unit is being replaced.
Item Description
1 Hose Clamp 1/2" ........................................b
2 Elbow 1/2" ...................................................b
3 Hose Fitting 1/2" Pipe to 1/2" Hose ............b
4 Water Hose 1/2" ID .....................................b
5 Manifold Gasket N14976 ......................a & c
6 Manifold Lockwashers 35W51020 ..............c
7 Manifold Bolts 08W12028 ...........................c
8 Discharge Manifold 100691C ......................c
9 Discharge Line KN17500 ............................d
10 Pipe Plug 1" 7 x 103 (Turbo Outlet)............d
11 Fuel Pump Drive Coupling SN3072BP .......d
12 Pipe Plug 1/8" 7 x 106 ................................a
13 Drive Coupling SN3072BN .........................d
14 Coupling Nut 2X5009 ..................................a
15 Drive Sleeve 2 3/4" long SN3072BM..........d
A Intake Manifold Mounting Flange
B Governor Mounting Flange
Comment Key:
a Provided with Compressor
b Part of SN3502 Kit
c Part of SN3711K Kit
d Order from Haldex
EL13040X
EL16040X
10
9
2
13
3
1
4
11
Oil Feed Options
Comment