General Safety Information; Specific Safety Rules - Matco Tools MUC12S Instrucciones De Operación

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
SAVE THESE INSTRUCTIONS!

GENERAL SAFETY INFORMATION

(FOR ALL BATTERY OPERATED TOOLS)
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
Work Area Safety
1 . Keep your work area clean and well lit .
Cluttered benches and dark areas invite accidents .
2 . Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases, or dust .
Power tools create sparks which may ignite the dust
or fumes .
3 . Keep bystanders, children, and visitors away while operating
a power tool . Distractions can cause you to lose control and
endanger others .
Electrical Safety
4 . A battery operated tool with integral batteries or a separate
battery pack must be recharged only with the specified
charger for the battery . A charger that may be suitable for
one type of battery may create a risk of fire when used with
another battery .
5 . Use battery operated tool only with specifically designated
battery pack . Use of any other batteries may create a risk
of fire .
Personal Safety
6 . Stay alert, watch what you are doing, and use common sense
when operating a power tool . Do not use tool while tired or
under the influence of drugs, alcohol, or medication .
A moment of inattention while operating power tools may
result in serious personal injury .
7 . Dress properly . Do not wear loose clothing or jewelry .
Contain long hair . Keep your hair, clothing, and gloves away
from moving parts . Loose clothes, jewelry, or long hair can be
caught in moving parts .
8 . Avoid accidental starting . Be sure switch is in the locked or
off position before inserting battery pack . Carrying tools with
your finger on the switch or inserting the battery pack into a
tool with the switch on invites accidents .
9 . Remove adjusting keys or wrenches before turning the tool
on . A wrench or a key that is left attached to a rotating part
of the tool may result in personal injury .
10 . Do not overreach . Keep proper footing and balance at all
times . Proper footing and balance enable better control of
the tool in unexpected situations .
11 . Use safety equipment . Always wear eye protection .
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions .
MUC12S
MUC12S 12V Screwdriver
2
Tool Use and Care
12 . Use clamps or another practical way to secure and support
the workpiece to a stable platform . Holding the work by hand
or against your body is unstable and may lead to loss of
control .
13 . Do not force tool . Use the correct tool for your application .
14 . Do not use tool if switch does not turn it on or off . A tool
that cannot be controlled with the switch is dangerous and
must be repaired .
15 . Disconnect battery pack from tool or place the switch in
the locked or off position before making any adjustments,
changing accessories, or storing the tool . Such preventive
safety measures reduce the risk of starting the tool
accidentally .
16 . Store idle tools out of reach of children and other untrained
persons . Tools are dangerous in the hands of untrained users .
17 . When battery pack is not in use, keep it away from other
metal objects like: paper clips, coins, keys, nails, screws,
or other small metal objects that can make a connection
from one terminal to another . Shorting the battery terminals
together may cause sparks, burns, or a fire .
18 . Maintain tools with care . Keep cutting tools sharp and clean .
Properly maintained tools with sharp cutting edge are less
likely to bind and are easier to control .
19 . Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may affect
the tool's operation . If damaged, have the tool serviced before
using . Many accidents are caused by poorly maintained tools .
20 . Use only accessories that are recommended by the
manufacturer for your model . Accessories that may be
suitable for one tool may create a risk of injury when used on
another tool .
Service
21 . Tool service must be performed only by the MATCO
authorized service centers listed . Service or maintenance
performed by unqualified personnel may result in a risk of
injury . Repair by unqualified personnel, use of unauthorized
parts, and failure to follow maintenance instructions may
create a risk of shock or injury .
SAVE THESE INSTRUCTIONS!

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
replace strict adherence to cordless product
safety rules. If you use this tool unsafely or
incorrectly, you can suffer serious personal injury.
1 . Hold tool by insulated gripping surfaces when performing
an operation where the cutting tool or adapter may contact
hidden wiring . Contact with a "live" wire will also make
exposed metal parts of the tool "live" and shock the operator .
12/20/11