Specific Safety Instructions; Instructions For Use; Assembly - stayer SS210 Manual De Instrucciones

This manual is consistent with the date of manufacture of your
machine, you will find information on the technical data of the
machine acquired manual check for updates of our machines on
the website: www.grupostayer.com
The machine is intended for sawing wood, plastic, metal and
building materials while resting firmly on the workpiece. It is
suitable for straight and curved cuts. When using the appropriate
bimetal saw blades, it is possible to cut flush to the workpiece
surface.
1. Contents
2. Specific safety instructions ................................... 14
3. Instructions for use ................................................ 14
3.1 Assembly ...................................................................... 14
3.2 Ilustrated description .................................................... 15
4. Operating instructions ........................................... 15
4.1 Placement and Testing ................................................. 15
4.2 General instructions for use.......................................... 15
5. Maintenance and service instructions ................. 16
5.1 Cleaning ....................................................................... 16
5.2 Repair service ............................................................. 16
5.3 Warranty ...................................................................... 16
5.4 Disposal and recycling.................................................. 16
6. Regulations ............................................................. 16
6.1 Technical Data .............................................................. 16
6.2 EU declaration of conformity ........................................ 17

2. Specific safety instructions

- Cutting accessory contacting a "live" wire may make ex-
posed metal parts of the power tool "live" and could give
the operator an electric shock.
- Keep hands away from the sawing range. Do not reach
under the workpiece. Contact with the saw blade can lead to
injuries.
- Apply the machine to the workpiece only when switched
on. Otherwise there is danger of kickback when the cutting tool
jams in the workpiece.
- When sawing, the adjustable footplate 2 must always faces
against the workpiece. The saw blade can become wedged
and lead to loss of control over the machine.
- When the cut is completed, switch off the machine and
then pull the saw blade out of the cut only after it has come
to a standstill. In this manner you can avoid kickback and can
place down the machine securely.
- Use only undamaged saw blades that are in perfect condi-
tion. Bent or dull saw blades can break, negatively influence
the cut, or lead to kickback.
- Do not brake the saw blade to a stop by applying side pres-
sure after switching off. The saw blade can be damaged,
break or cause kickback.
- Clamp material well. Do not support the workpiece with
your hand or foot. Do not touch objects or the floor with
the the saw running. Danger of kickback.
ENGLISH
14
- Use suitable detectors to determine if utility lines are hid-
den in the work area or call the local utility company for as-
sistance. Contact with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explosion.Penetrating
a water line causes property damage or may cause an electric
shock.
- Secure the workpiece. A workpiece clamped with clamping
devices or in a vice is held more secure than by hand.
- Always wait until the machine has come to a complete
page
stop before placing it down. The tool insert can jam and lead
to loss of control over the power tool.

3. Instructions for use

Read all safety warnings and all instructions. Failu-
re to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Placement
- When working with the machine, always hold it firmly with
both hands and provide for a secure stance. The power tool
is guided more secure with both hands.
- The tool is provided with a base plate 2 which should be settled
permanently against the workpiece while this sawing.

3.1 Assembly

Before any work on the machine itself, pull the
mains plug.
When mounting the saw blade, wear protective glo-
ves. Danger of injury when touching the saw blade.
When changing the saw blade, take care that the
saw blade holder is free of material residue, e.g.
wood or metal shavings.
Selecting a Saw Blade
Use only saw blades with ½" universal shank. The saw blade
should not be longer than required for the intended cut. Use a
thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A)
- Press the unlock button on the base plate 6.
Turn in the direction of clockwise the knurled housing saw blade
3 and insert the saw blade 1 in the front, in the housing of the
saw blade 3. Affirm the housing 3 this when the blade.
Check the tight seating by pulling on the saw blade.
A loose saw blade can fall out and cause injury.
For certain work, the saw blade 1 can also be turned through
180° (with the teeth pointed upwards) and re-inserted again.
14