GiBiDi EVO 240/101-76 E Instrucciones De Instalación Y Reglaje página 11

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

Operator for roll-up doors
The operator should be fixed, lined and the pulley must turn freely.
Make a hole Ø 12 mm. in the last canvas of the shutter at the same location of the hole and nut M10 of the pulley
(Fig. 10). If the shutter is waved or not regular, it is necessary to couple a flat metal piece of 1 meter to the pulley.
Travel the electric cable trough the shaft's hole de Ø 12 mm. (Fig. 11), avoiding any contact with the rotating parts
and make the wires. In case of motor with electric brake travel also the brake cable through the hole of Ø 12 mm.
drilled in the shaft, and mount the manual release.
For a proper release the flexible cable of the brake should not do any exaggerated curve.
ELECTRIC WIRE (Fig. 11)
It is very important to respect the connection of the common of the motor (N) and the earth connection. The
model with electro brake comes already wired. If the automatism is not provided with electro brake, bridge the
contacts (A, B fig 11). With electro brake, remove the bridge and on the same terminals connect the reel.
SECURITY STANDARD: The connection wires should come from a differential switch.
CHECKING THE OPERATION DIRECTION (Fig. 12)
Place the closing stop collar (C1) until the click of the opening micro-switch is heard (fig. 12) Give power, if the motor
stops at closing it's correct. If not, cut the power and change the position of the phase wires, or the two wires that go
to the control unit, or activate it manually by means of the key switch. Continue respecting the common jumper of
the motor (N).
REGULATION OF THE OPENING LIMIT-SWITCH (Fig. 13)
Fix the door to the pulley with the supplied pulley fixing ring, fan-type lock washer and M12 countersunk
bolt(fig.13). Move manually the opening stop collar (D1) up to the regulation of the opening of the door. [Fig.12).
Check the travel and adjust it if necessary.
REPLACEMENT OF THE ELECTRIC WIRE
For a correct replacement of the electric wire respect the following indications:
Cut out the electric connection
Take out the lid that covers the micro switch removing the 2 screws.
Unscrew the 3 wires and the ground.
Remove the stuffing box and take out the cable (if does not slide cut it).
Loosen all the wire fixings to the electronic board.
Unwire the cable from the board.
Substitute the wire for another cable with standard (4x1.5HO5 VVF).
Wire the new cable doing the same operations in the inverse sense.
Switch on the motor and check its correct direction. If not, change the black wire and the brown one. Make
reference to the connection board indicated in the assembling instructions paying attention to the position of the
common motor (N).
GUARANTEE
The Company guarantees all products against any production fault for a period of 2 years following the supply date.
LIABILITIES
The Company is obliged to undertake repairs of the equipments under guarantee, following revision by the
technical department.
All the equipments that, due to emergency, are delivered before the decision they are actually under guarantee, will
be considered as a standard order to be paid. Faulty equipment replaced under guarantee will remain of property of
the Company. The replacement of such equipments will be on the installer's account and charge.
CANCELLATION
The equipment will not be under guarantee in the following cases:
-
incorrect choice of the equipment given the door's characteristics
-
the mounting and connecting instructions have not been followed
-
payment has not been settled
10

Publicidad

Tabla de contenido
loading

Productos relacionados para GiBiDi EVO 240/101-76 E

Este manual también es adecuado para:

Evo 240/101-76 bmeEvo 240/101-76Evo 240/101-76 bm

Tabla de contenido