BLACK&DECKER KD1250K Manual De Instrucciones página 13

or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of
untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by Black &
Decker, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
FEATURES (FIG. A)
1. On/Off switch
2. Speed selector switch
3. Handle
4. Operating mode selector
5. SDS chuck
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
6. Side handle
7. Depth rod
8. Drilling mode selector
ADDITIONAL POWER TOOL SAFETY
f Wear ear protectors. Exposure to noise can cause
hearing loss.
f Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
f Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
f Never use a chisel accessory in rotary mode. The
accessory will bind in the material and rotate the drill.
f Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it
unstable and may lead to loss of control.
f Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
f Avoid touching the tip of a drill bit just after drilling,
as it may be hot.
f This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
f The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
f Use a face or dust mask whenever the operations may
produce dust or flying particles.
Construction
Earthing ASSEMBLY
Terminal
Warning! Before assembly, make sure that the tool is
Safety Alert
switched off and unplugged.
Symbol
Revolutions
or Recipro-
Fitting the side handle and depth rod (Fig. B)
cation per
minute
f Turn the handle counter-clockwise until you can slide
the side handle (6) to the front of the tool as shown.
f Rotate the side handle into the desired position.
f Tighten the side handle by turning the handle in the
direction of clockwise.
f Loosen the knob (9).
f Insert the depth bar (7) in the mounting hole as shown.
f Adjust the drilling depth as described below.
f Tighten the knob (9).
ENGLISH • 13
WARNINGS