How To Use - babymoov A002028 Instrucciones De Uso

• Leave the bottle warmer to cool for about 15 minutes before
using it again. Never touch the inside of the tank while the
appliance is in use, or immediately after use.
• Always unplug the appliance before cleaning or filling and after
each use.
• Do not leave the power cable at the edge of a table or work-
surface. Do not place it on a hot surface. Do not leave the
power cable dangling where a child could reach it.
• In the interests of safety, only use Babymoov accessories and
spare parts and never dismantle the appliance.
• Avoid using your appliance if it is not working properly or if it
is damaged. If this happens, contact the Babymoov after-
sales service.
a. Measuring device
b. Warming tank
c. Jar basket
Points to respect for trouble-free use:
- Always check that the bottle is slightly open.
- Always remove the lid from the jar.
- Optimum heating will be guaranteed provided operation is not interrupted.
- Use tap water only, with no added product.
PLEASE NOTE: always use the adapter ring and the basket to warm up baby bottles and jars.
By using the amounts of water indicated in the tables below, a baby bottle or jar will be heated to 30 °C / 33 °C.
The quantities given are an indication only; if you think the result is too hot or not hot enough for your baby, don't hesitate to reduce
or increase the quantities of water.
Take care: the quantities of water given correspond to a polycarbonate bottle without a removable base.
Using the appliance at home
Put the bottle-warmer on a flat and steady
surface. Make sure the bottle-warmer's power
cable is out of the reach of children.
Plug the power cable into a power outlet.
1-2. Fill up the measuring device (a) with
water by following the doses reported
here to the side and then pour the water
into the warming tank (b).
3. Put the baby bottle in the bottle-warmer's
warming tank (b).
4. If using a standard/small baby bottle, place
the adapter ring (d) around the bottle to
better warm up the contents.
5. To warm up a jar, place it in the designated
basket (c) and then in the warming tank (b).
6. Press the ON button (e) to start the heating
cycle. The backlit ring (h) will turn red, which
means that the heating cycle is in progress.
CAUTION! The steam that comes out during
the heating cycle is very hot. Do not put your
hands on the appliance when it is in use.
8
d. Adapter ring
e. ON button
f. Cigarette-lighter adapter
TULIPE HOME/CAR BOTTLE-WARMER • Instructions for use
Using the appliance in the car:
• Never use the bottle-warmer while the vehicle is in motion.
Leave your engine on when using the bottle-warmer to avoid
running the battery down.
• The cigarette-lighter adapter is specially designed for this bottle-
warmer: do not use it with other appliances.
• Regularly check your vehicle's cigarette lighter.
• Clean it as required.
• If you have just used your car's cigarette lighter, let it cool down
for five minutes in the open position before plugging in the
bottle-warmer.

HOW TO USE

Quantity of water to put
in the measure, when
Amount of milk
in the bottle
prepared with water at
60 ml
90 ml
120 ml
150 ml
180 ml
210 ml
240 ml
270 ml
300 ml
330 ml
Jar to put in the measure
120 g
200 g
250 g
g. Power cable
h. Backlit ring
the bottle has been
room temperature.
7 ml
8 ml
10 ml
11 ml
12 ml
13 ml
14 ml
15 ml
16 ml
17 ml
Quantity of water
for one jar.
10 ml
12 ml
15 ml
Quantity of water
to put in the measure
for a bottle prepared
and placed in the
refrigerator.
10 ml
12 ml
12,5 ml
13 ml
13,5 ml
14 ml
14,5 ml
15 ml
15,5 ml
16 ml
Quantity of water
to put in the measure
for a jar kept in the
refrigerator.
18 ml
22 ml
28 ml