Errebi LS8 Manual De Instrucciones página 13

1. PreSentation and generaL aSPeCtS
1.1 generaL aSPeCtS
Following the evolution of the LS family, the launch of the new LS8 is
presented.
As such, and taking the renowned and successful LS7 as a base, a more
robust and compact machine has been developed that clones most of the
encrypted and fixed, automatic and PC mode transponder families available on
the market:
•Megamos fixed code
•Temic fixed code
•Nova fixed code
•Philips fixed and encrypted code
•Texas fixed and encrypted code
This evolution is true to the philosophy for the entire LS range, which can be
translated as "the simpler the better for the user".
In line with this maxim, the LS8 still has the usual READ/COPY buttons
present in the entire range.
In this new evolution, JMA has worked considerably on the technical simpli-
fication of the solution provided as a whole (LS+TPX Cloner+TX4TECH).
In fact, substantial effort has been made to compact all the external hard-
ware and cabling used previously (TPX Cloner + TX4TECH) whose functiona-
lity is supplied with the codes that bear the original keys from the Texas and
Philips Crypto families respectively, in one unit.
1.2 tranSPort and PaCkaging
The machine is supplied protected by polystyrene packing and inside a
cardboard box with the following dimensions and weight:
• Width = 275 mm.
• Length = 320 mm.
• Height = 170 mm.
• Weight = 550 g.
When unpacking the machine, check carefully to see if it has been damaged
during transportation. If you find any problems, please contact ERREBI tech-
nical or customer service department and do not use the machine.
2.teChniCaL SPeCiFiCationS
The LS8 duplicating machine, in addition to offering the same and the complete
reading and cloning range of the main transponder manufacturers, offers comple-
te information on the detail of these readings.
Also, with the compacting of the product (integration of the two external clo-
ners (TPX+TX4TECH), on a single plate) the errors have been suppressed that
are often generated by the client when connecting between the different
devices (LS7 TX4TECH TPX).
The machine is updated using the upper USB port (known as the TR).
The other USB port (known as the CL), is enabled for updating the new
compact Cloner (TPX+TX4TECH), so that new vehicle models can be easily
added for later cloning.
2.1 the maChine'S SuPPLementary eLementS
After unpacking the LS8 duplicating machine, the following components
should be found:
• Power supply 100-240 Vac / 50-60 Hz and 9V / 2.5 A.
• USB cable type A-B (1.5 m long), for interconnection between the PC and
the LS 8.
• Instructions manual.
• TX4 support (two units).
2.2 the maChine'S main eLementS
• Two push buttons (READ and COPY).
• One on/off switch.
• One female DB9 connector for future RS 232 series line connections.
• Two USB connectors (CL for CLoner and TR for LS8).
• One DC power supply connector.
• One 4x20 character alphanumeric display.
3. Starting the maChine
3.1 Situating the aPPLianCe
Once the machine has been carefully unpacked, it must be placed on a
surface that is not made of metal or any other material that may generate
electromagnetic interference when reading, given that the antenna is the
most sensitive area to interferences and therefore to the metal components
that distort the signal captured from the key as well as the tuning frequency.
As an example:
A correct location for situating the machine may be a wooden desk.
It must also be taken into account that the machine must be situated at
a distance of at least between 80 and 100 cm from any electromagnetic
interference source (operator screens, televisions, electrical communication
elements, motors, walky-talkies, mobile phones, etc.).
3.2 inStaLLing and Fitting the equiPment
One positioned correctly, all the material received with the appliance can be
installed.
To do this, proceed as follows:
1. Check that the material in the box received from the manufacturer is in
accordance with point 2.1 of this manual in reference to the elements the
machine includes.
2. Check there is a 110/220V power socket available in the premises and that
the power supply received is correct: 100-240 Vac / 50-60Hz and 9V /2A.
Connect the power supply to the LS8.
The inclusion of the (4x20) alphanumeric display on the LS8 enables reading
of all the transponders to be optimised, thus offering detailed and complete
information about them.
Following, and to summarise, the attached table shows the messages
that appear when reading an original key as well as the transponder to be
inserted for cloning the key.
reF. reSuLt on LS8
errebi
t01
T01 Philips Fixed
Copy on T05/01
ID 30C7F1FF07F0E3C7
711C07FEE3FF7F00
tP02
T02 Texas Fixed
Copy on TX1
TI ID 00007E62409A00
0000000074717E0000
t03
T03 Megamos fixed code
Copy on T05
ID FF81342019B9C710
FF81342019B9C710
t04
T04 Temic fixed code
Copy on T05
ID 9E8D77DF4000001C
9E8D77DF4000001C
aCtuaL tranSPonder
Philips code Fixed Wedge format
Code example on T01 / ID 33
Texas Code Fixed Glass format 23 mm
Code example on a T02 / ID 4C
Megamos code Fixed Glass 13 mm
Code example on a T03 / ID 13
Temic code Fixed Wedge format
Code example on a T04 / ID 11-12