Errebi LS8 Manual De Instrucciones página 16

4.1.2 inforMation suPPlied when coPying a texas cryPto
Next, the process will be shown for cloning a Texas Crypto transponder that
is mounted for example on a Ford Focus (2007) and the messages shown on
the LS8 display:
INSERT KEy
PRESS READ
Once the original key is analysed, the following detailed information will be
shown:
• ERREBI code for the chip that holds the key (T 20).
• Transponder type and manufacturer (Texas Crypto).
• Manufacturer of the vehicle that uses it (FORD).
• The ERREBI transponder that must be used for cloning this key (TX2).
• Information about the transponder's internal structure, which will be
different depending on the chip manufacturer. As an example, a FORD key
would be (Password: 03, Manufacturer's code: 01, Serial number: 00 and
User serial number: 2FAC03, bits locked, which refers to the write-protected
information pages, 0010 (Pag3 LOCK) and finally if the old DST40 algorithm
or the new DST80 is used).
T20 TExAS CRy FORD
COPy ON Tx2
PW: 03 ID: 00 2FAC03
mC: 01 LCK: 0010 DST40
After entering the ERREBI (TX2) transponder on which the cloning on the
antenna will be carried out, press the COPY button.
READy TO COPy
PRESS COPy
The LS8 will begin to analyse the transponder from the original key
entered.
PLEASE WAIT
............................
Once discovered, this information will be written on the TX2 and it will beep
once if the copy is executed correctly.
COPy OK
ExTRACT KEy
4.1.3 inforMation suPPlied when coPying a PhiliPs cryPto ii.
To finalise, it shows the cloning process of a second generation Phillips
Crypto transponder, HT2, used by a Citroen C3 and the messages that would
display TRS EVO.
INSERT KEy
PRESS READ
Once the original key is analysed, the following information will be shown:
• ERREBI code for the chip that holds the key (T 12).
• Chip model included (PCF7941).
• Transponder type and manufacturer (PHC – Philips Crypto).
• The ERREBI transponder that must be used for cloning this key (TX4).
•Information about the transponder's internal structure, which will be
different depending on the chip manufacturer. As an example, a CITROEN
key would be (Serial number: B9B66969, if it is write-protected (LOCK) and
the type of coding used (Manchester)).
T12-PCF7941 PHC
COPy ON Tx4
ID: B9B66969
mODE LOCK mANCHESTER
To activate the TX4TECH mode supported by Philips Crypto, the process com-
mences by pressing the COPY key on the original key.
DO NOT REmOvE THE KEy
PRESS COPy
While the HT2 algorithm used by Philips Crypto second generation is being
loaded into the memory, the LS8 will display the following message:
PLEASE WAIT
............................
When the FPGA has loaded the corresponding memory, the following will be
shown on the display:
TPx CLONER READy
............................
And the LS 8 will be ready for analysing and completing the following steps,
requesting a return to read the original key:
PRESS [READ]
Next, the transponder's type and brand will be indicated, as well as whether
it is an original transponder or a copy (Philips crypto type):
PHILIPS CRPTO
PHILIPS CRyPTO TyPE
A Virgin TX4 must then be entered to configure it in capture mode (Sniff)
and to be able to capture the data, verifying that the copy has been made
correctly.
INSERT vIRgIN Tx4
PRESS [COPy]
SuCCESS
gO TO CAR & SNIFF
The LS8 will wait until the data stored in a TX4 are introduced (these data
contain the information flows that are transmitted between the ECU and the
original key).
INSERT SNIFF Tx4
PRESS [READ]
This data will be stored in the LS8's RAM memory so that it is available
during the search process.