Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Fishwire (provided)
Fastener Kit: 24910F
Wrenches: 5/8", 11/16"
Drill Bits: none
FORWARD
PASSENGER SIDE FRAME RAIL SHOWN
j
Qty. (2)
U-BOLT 7/16-20
k
CONICAL WASHER – 7/16
Qty. (4)
l
NUT – 7/16-20
Qty. (4)
m
Qty. (2)
CARRIAGE BOLT 7/16-14 X 1-1/2
1.
Place the U-bolts in rear most indentation in frame extension as shown.
2.
Raise hitch into place and loosely install the conical washers and 7/16-20 (fine thread) nuts.
3.
Using the fishwire (provided) insert coiled end thru forward attachment hole in hitch, into the frame, and out the access hole. Slide
block on and thread carriage bolt into the coil of the fishwire. Keep block and bolt separate until inside frame (see photo above).
Pull carriage bolt and block into position with the thread showing below hitch side bracket. Install lock washer and 7/16-14
(course thread) nut.
4.
Tighten all fasteners to the required torque specifications.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
©
2014,2015 Cequent Performance Products. Printed in Mexico
Installation Instructions
Ford Fiesta Sedan
FASCIA
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
j
FRAME
EXTENSION
n
m
k
l
Tighten all 7/16 fasteners with torque wrench to 50 Lb.-Ft. (68 n*m)
m
n
FRAME
k
l
n
BLOCKS – 3/16 X 1 X 2
Qty. (2)
o
LOCK WASHER – 7/16
Qty. (2)
p
NUT – 7/16-14
Qty. (2)
q
Qty. (1)
Fishwire
Sheet 1 of 3
24910N
Part Numbers:
24910
60342
77297
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000LB (908Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC 3, 4
m
j
n
o p
ATTACHMENT
10-05-15
ACCESS
HOLE
FORWARD
HOLE
o p
Rev. C
Publicidad
Manuales relacionados para Cequent Performance Products 24910
Resumen de contenidos para Cequent Performance Products 24910
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © Sheet 1 of 3 24910N 10-05-15 Rev. C 2014,2015 Cequent Performance Products. Printed in Mexico...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systè mes d’attelage. ©2014,2015 Cequent Performance Products. Feuille 2 de 3 24910N 10-05-15 Rev.
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. © Hoja 3 de 3 24910N 10-05-15 Rev. C 2014, 2015 Cequent Performance Products - Impreso en México...