Publicidad
Enlaces rápidos
KLT500/KLR500
Installation Instructions
Инструкция по установке
Instrucciones de Instalación
הוראות התקנה
English, Русский, Español, עברית
1
2
KLT500/KLR500 LCD Keypads
KLT500 and KLR500 are touch and silicon-rubber keys (respectively) graphic LCD keypads, designed for the FORCE Series intruder alarm
systems. The two keypads connect to the control panel over the bus. Up to 16 keypads can be connected to the FORCE.
The KLT500 and the KLR500 have a modern and sleek design that fits every indoor decoration.
The two keypads have four LEDs - Arm, Ready, AC, Alert/Fault - and a buzzer for various panel status indications.
The two keypads have settings for backlight, contrast, buzzer volume and ID no., and a tamper switch for detecting the opening of
the enclosure.
For complete information, see the FORCE's Installation guide (P/N: 4410459).
Technical specifications
Screen size: 128X64 pixel
Voltage levels: 0, +12V
Operating Voltage Range: 9-14 VDC
Current Consumption: 50mA idle, 90mA max.
Content of the product package
KLT500/KLR500 keypad + terminal block
How to install the KLT500/KLR500
Follow the next steps to connect the keypads.
1.
Insert a slotted screwdriver to the notches on the keypad's bottom, press gently and remove
the backplate.
2.
Pass the BUS wires through the opening at the backplate.
3.
Mount the backplate on a flat surface.
4.
Connect the four BUS wires to the control panel: each wire connects between terminals with the same number on the keypad and
the control panel (1-1, 2-2, etc.).
5.
Attach the keypad to the mounted backplate, top side first, and press until clicked.
Ordering Information
KLT500: P/N 8415011
KLR500: P/N 8415002
3
4
Sizes: 15 x 12 x 2cm
Weight: 235gr
CE compliance
Operating Temperature: -10°C to +55°C
Humidity (Max.): 93% R.H., Non-condensing.
This guide
1
FORCE's control panel
2
BUS Cable
3
Keypad (back side)
4
Terminal Connector
1
Control panel FORCE
2
Cable para el BUS de conexión
3
Teclado (sin cobertura posterior)
4
Bloque terminal de conexiones
-1-
1
Контрольная панель FORCE
2
4-х проводной кабель шины BUS
3
Клавиатура (вид сзади)
4
Клеммная колодка
לוח הבקרה של
FORCE
BUS
)י
לוח המקשים (צד אחור
טרמינל בלוק
1
-
כבל ה
2
3
4
Publicidad
Manuales relacionados para Pima KLT500
Resumen de contenidos para Pima KLT500
- Página 1 KLT500/KLR500 LCD Keypads KLT500 and KLR500 are touch and silicon-rubber keys (respectively) graphic LCD keypads, designed for the FORCE Series intruder alarm systems. The two keypads connect to the control panel over the bus. Up to 16 keypads can be connected to the FORCE.
- Página 2 KLT500/KLR500 – Teclados de LCD Los teclados LCD gráficos KLT500 y KLR500 son teclados táctiles y con teclas de caucho de silicona (respectivamente), diseñados para los sistemas de alarma de la serie FORCE. Ambos teclados se conectan a través del BUS del sistema. Se pueden conectar hasta 16 teclados a un sistema de alarma FORCE.
- Página 3 Limited Warranty PIMA Electronic Systems Ltd. does not represent that its product may not be compromised and/or circumvented, or that the Product will prevent any death, personal and/or bodily injury and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate warning or protection.
- Página 4 Garantía Limitada PIMA Electronic Systems Ltd. no garantiza que su Producto no haya sido o sea puesto en riesgo o que no sea evadido o que no sea o haya sido saboteado o alterado de alguna forma o que no haya sufrido o sufra alguna forma de manejo malintencionado así como tampoco garantiza que el Producto vaya o pueda prevenir cualquier muerte y/o daños corporales y/o daños a la propiedad o cualquier otra pérdida resultado directo o indirecto de vandalismo,...