Tabla de contenido
Publicidad
CHAPTER 4: CARE & MAINTENANCE
CAPÍTULO 3: CUIDADO Y MANTENIMIENTO
CABLE INSPECTION & MAINTENANCE (continued):
Cable Tension:
Tensión de cables:
Asegúrese de que los cables se ajustan para suprimir cualquier holgura con los terminales roscados. Normalmente están
Ensure that the cables are adjusted to remove any slack using the threaded end fittings. These are normally located at the
localizados en la conexión de la columna de pesas. Dependiendo de la máquina, puede haber varios terminales roscados
weight stack connection. Depending upon the machine, there may be multiple threaded fitting on multiple cables. You
en varios cables. Puede determinar si hay demasiada holgura al realizar el ejercicio. Cuando comienza a mover un agarre
CHAPTER 4: CARE & MAINTENANCE
can determine if there is too much slack by performing the exercise. As you start to move a load arm or handle, the weight
o brazo de carga, la columna de pesas debería elevarse inmediatamente. Si no es así, hay que ajustar la tensión del cable.
stack should lift immediately. If not, the cable tension needs to be adjusted.
OTHER SCHEDULED PREVENTIVE MAINTENANCE:
Para ajustar la tensión del cable, afloje la tuerca
To adjust the cable tension, loosen the cable nut
del cable que está situada en el perno del cable
TRUE recommends that scheduled maintenance be performed by a qualified service technician. Please contact your
that is located on the cable bolt connected to the
conectado a la placa superior. Apriete el perno
dealer or visit www.truefitness.com to contact a local TRUE authorized service technician.
top plate. Tighten the cable bolt until the top plate
del cable hasta que la placa superior apenas esté
is barely lifted off of the first weight plate and then
Monthly:
separada del primer disco y entonces vuelva a
re-tighten the cable nut.
apretar la tuerca del cable.
Clean guide rods and lubricate with a Teflon grease if equipped with guide rods.
Every 6 months:
Lubricate pivot bearing and linear bearings with lithium grease.
CLEANING THE EQUIPMENT:
Daily Cleaning:
Wipe all machines with a water dampened cloth and dry completely. This includes painted parts, chrome plated parts
(except guide rods), plastic parts, and upholstered pads. It is important not to leave parts damp. This will increase the
potential for corrosion to occur.
ATENCIÓN:
CAUTION:
CAUTION:
A minimum of 1/2 inch (12.7mm) of the threaded
Certain anti-bacterial cleaners and other harsh cleaning agents can induce corrosion on the machine components. These
Debe enroscarse un mínimo de 12,7 mm de la parte
roscada de perno del cable en la placa superior.
portion of the cable bolt must be threaded into the
solutions can also dry out and cause cracking and splitting on the upholstery.
*No debe estar visible más de 25,4 mm de la parte
top plate.
roscada del perno del cable.
*No more than 1 inch (25.4 mm) of the threaded
Heavy Duty Cleaning:
portion of the cable bolt should be visible.
Guide Rods (If Equipped): Clean and lubricate with a Teflon Spray. Be sure to coat the entire guide rod. Spraying
lubricant into the cap plate bushings is also recommended.
Chromed Adjustment Tubes: Wipe away dust and dirt before applying a Teflon spray lubricant. TRUE Fitness
recommends using TriFlow or a similar brand.
Linear Bearings: Clean the linear shaft and lubricate (as required) with Teflon based grease. Keeping linear bearings clean
and lubricated is critical to long life and good performance.
Handle Fittings (if applicable):
Accesorios de agarre (si procede):
Painted Frames: If you have scuff marks, grease or a heavy dirt buildup on frame components, start with a mild soap
Inspeccione los accesorios del cable donde se
solution or a diluted solution of a product such as Simple Green with a dilusion of 32:1. If you cannot remove the marks
Inspect the cable fittings where any handles are
unen los agarres al final del cable. Los accesorios
using those methods, use a car polish/cleaner. DO NOT use solvents such as lacquer thinner, mineral spirits or acetone.
attached to the end of the cable. The fittings supplied
proporcionados con esta máquina son mosquetones
For deeper scuff marks, use an automobile finish rubbing compound.
with this machine are load rated snap-links. Ensure
de carga nominal. Asegúrese de que el mosquetón
that the snap-link opens and closes easily and is fully
se abre y se cierra fácilmente y que está
Upholstery: For heavy duty cleaning, use a mild soap solution. This method should be sufficient in the majority of
engaged when closed. Replace the snap-link as
completamente enganchado cuando está cerrado.
instances. In severe stain cases, you can use a solution of 5-10% household bleach diluted with water. Be sure to test an
needed.
Sustituya el mosquetón cuando sea necesario.
inconspicuous area first. DO NOT use chemical cleaners on the vinyl upholstery. You can also use a lanolin based hand
cleaner to clean your upholstery. Wipe off after cleaning with a damp cloth and thoroughly dry. Plastic Parts: use a mild
soap solution to clean dirt and grease marks. Labels: use a mild soap solution to clean dirt and grease marks. Shrouds: use
a mild soap solution to clean dirt and grease marks.
True Fitness Technology • O'Fallon, MO • Teléfono: 800-426-6570/636-272-7100 • Truefitness.com
Truefitness.com / 800.426.6570 / 636.272.7100
Perno del
Cable Bolt
cable
Tuerca
Cable Nut
del cable
25,4 mm
1" (25.4 mm)
Máximo
Maximum
Fuerza
Fuse XL-0600
Placa superior
Top Plate
Página nº 31 de 37
40
Publicidad
Tabla de contenido
