Bosch PWS Professional 2000-230 JE Manual Original página 19

Ocultar thumbs Ver también para PWS Professional 2000-230 JE:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 33
OBJ_BUCH-2397-004.book Page 19 Wednesday, August 24, 2016 3:58 PM
Technical Data
Angle Grinder
Article number
3 603 ...
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder
spindle
Restarting Protection
Reduced starting current
Weight according to EPTA-
Procedure 01:2014
– with vibration-damping
auxiliary handle
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles generate brief voltage drops. Interference with other equipment/machines may
occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.25 ohm.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 92 dB(A); Sound power level
103 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
2
Surface grinding: a
=7.5 m/s
, K=1.5 m/s
h
2
Disk sanding: a
=4.0 m/s
, K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools
PWS 2000-230 JE
... CC6 0..
W
2000
W
1250
-1
min
6500
mm
230
M 14
mm
25
kg
5.5
kg
5.4
/II
Assembly
Mounting the Protective Devices
 Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance. For addresses, see section "Af-
ter-sales Service and Application Service".
2
,
2
.
Protection Guard for Grinding
Place the protection guard 5 on the spindle collar. Adjust the
position of the protection guard 5 to the requirements of the
operation and lock the protection guard 5 with the locking
screw 6.
 Adjust the protection guard 5 in such a manner that
sparking is prevented in the direction of the operator.
Protection Guard for Cutting
 For cutting with bonded abrasives, always use the pro-
tection guard for cutting 13.
 Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting 13 is mounted in the same
manner as the protection guard for grinding 5.
Cutting Guide with Dust Extraction Protection Guard
The cutting guide with dust extraction protection guard 23 is
mounted in the same manner as the protection guard for
grinding 5.
PWS 20-230
PWS 20-230 J
... C59 W..
... C59 V..
2000
2000
1250
1250
6600
6600
230
230
M 14
M 14
25
25
5.5
5.5
5.4
5.4
/II
/II
1 609 92A 222 | (24.8.16)
English | 19
PWS 1900
... C59 W..
1900
1170
6600
230
M 14
25
5.5
5.4
/II

Publicidad

Tabla de contenido
loading

Tabla de contenido