Technical Data; Important Installation Information - MAC Audio MPExclusive 1.0 XL El Manual Del Propietario

Dear MAC AUDIO Customer,
The MPExclusive 1.0 XL/MPExclusive 1.0 car hi-fi power amplifier will enable you to satisfy your high demands on sound reproduction
in your car. With its impressive deep-bass power reserves, low harmonic content and neutral reproduction, the MPExclusive 1.0 XL/
MPExclusive 1.0 takes car hi-fi to new heights. The amplifier is characterized by low operating current, rapid switching capabilities and
excellent temperature stability. Experience and enjoy how this high-tech machine perfectly reproduces magnificent sound.
Please read all of the owner's manual before installing and using the amplifier.
1.

TECHNICAL DATA

Max. output power (1 kHz sinus burst 2:8, B+=14.4V)
Nominal output power (DIN 45 324, B+=14.4V)
Max. output power (1 kHz sinus burst 2:8, B+=14.4V)
Nominal output power (DIN 45 324, B+=14.4V)
Loudspeaker impedance
Frequency response
Total harmonic content (DIN 45 403)
Weighted noise distance (IEC A)
Input sensitivity LOW LEVEL INPUT
Input impedance LOW LEVEL INPUT
Low-pass filter
Subsonic filter
Bass boost
Supply
Fuse
Sizes (W x H x D)
Weight
Max. output power (1 kHz sinus burst 2:8, B+=14.4V)
Nominal output power (DIN 45 324, B+=14.4V)
Max. output power (1 kHz sinus burst 2:8, B+=14.4V)
Nominal output power (DIN 45 324, B+=14.4V)
Loudspeaker impedance
Frequency response
Total harmonic content (DIN 45 403)
Weighted noise distance (IEC A)
Input sensitivity LOW LEVEL INPUT
Input impedance LOW LEVEL INPUT
Low-pass filter
Subsonic filter
Bass boost
Supply
Fuse
Sizes (W x H x D)
Weight
SUBJECT TO TECHNICAL CHANGE
2. FEATURES
· Complementary push-pull final stage
· Stable at 2 ohms
· Low-pass (subwoofer) and subsonic filter with infinitely adjustable separating frequencies
· Infinitely variable bass equalisation
· Adjustable input sensitivity
· Electronic protective circuit against short circuiting, DC offset and excess temperature
· Mute switch for suppressing switch-on crackle interference
· Low-level outputs (cinch jacks) for connecting additional amplifiers
· Capsulated loudspeaker and power-supply screw terminals
· Status indicator (green LED) and overload indicator (red LED)
· Remote control for volume control
3.

IMPORTANT INSTALLATION INFORMATION

· This appliance may only be connected to a 12 volt system with negative ground.
· The heat radiated when the amplifier is used means that sufficient air circulation is required at the place of installation. It is very
important that the cooler's cooler ribs do not contact any metal plating or any surfaces which could impair air circulation. The
amplifier may not be installed in small confined spaces or spaces without air circulation (e.g. spare wheel recess or under the vehicle
carpeting). Installation in the boot is recommended.
· Install the amplifier in such a way that it is protected as far as possible against vibrations and dust and dirt.
MPExclusive 1.0 XL
900 W on 4 Ohm
275 W on 4 Ohm
1500 W on 2 Ohm
400 W on 2 Ohm
2 – 8 Ohm
5 – 300 Hz (-3 dB)
< 0.05 % (1 kHz)
> 100 dB
0.4 – 4 V
20 kOhm
40 – 300 Hz, 12 dB per octave
10 – 40 Hz, 12 dB per octave
0...12 dB at 45 Hz
+12 V (10 – 15 V), minus to ground
2 x 30 A
400 x 55 x 226 mm
3.55 kg
MPExclusive 1.0
400 W on 4 Ohm
150 W on 4 Ohm
600 W on 2 Ohm
175 W on 2 Ohm
2 – 8 Ohm
5 – 300 Hz (-3 dB)
< 0.05 % (1 kHz)
> 100 dB
0.4 – 4 V
20 kOhm
40 – 300 Hz, 12 dB per octave
10 – 40 Hz, 12 dB per octave
0...12 dB at 45 Hz
+12 V (10 – 15 V), minus to ground
2 x 15 A
290 x 55 x 226 mm
2.45 kg
7