Stanley FATMAX SFMCMS2653 Traducido De Las Instrucciones Originales página 15

• Always release bail handle to turn mower off, remove safety
key and battery pack when leaving it unattended even for a
short period of time.
The following suggestions will help you to
obtain optimum run time from your cordless
mower:
• Slow down in areas where the grass is especially long
or thick.
• Avoid mowing when the grass is wet from rain or dew-
soaked.
• Cut your lawn frequently, especially during high
growth periods.
nOTE: It is recommended that your mower be recharged after
use to prolong the battery life. Frequent charging will not harm
your battery, and will ensure that the battery is fully charged
and ready for its next use. Storing battery not fully charged will
shorten battery life.
Transmission Thermal Switch

DANGER: Rotating blades can cause serious injury.
To prevent serious injury, remove safety key and
battery pack when unattended, or when charging,
cleaning, servicing, transporting, lifting, or
storing mower.
The thermal switch protects the self drive motor from
overloading and overheating that could damage the motor.
The thermal switch will automatically shut down power
to the self drive motor (not the blade motor) in the case
of overheating.
The reset of the thermal switch is automatic when the
transmission's internal temperature drops below 158° F (70° C)
and the self drive bail handle is in the released (off ) position.
When the thermal switch activates:
1. Remove safety key and battery pack.
2. Clean the self drive motor housing of debris. This will keep
the transmission cool. Refer to Troubleshooting Guide
in this manual.
3. Check that the wheels are spinning freely.
nOTE: Harsh conditions (high outside temperature, slopes,
high grass, etc.) can overheat the transmission and activate the
thermal switch if your mowing pace is too slow. Increase the
mowing speed to improve the ventilation.
4. If after performing these actions the thermal switch
continues to shut down the power to the transmission stop
using the mower and contact your local dealer.
MAINTENANCE

DANGER: To reduce the risk of serious personal
injury, turn unit off, remove safety key, and remove
battery packs before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
Removing and Installing Blade (Fig. J–L)

DANGER: RISK OF INJURY. WHEN REASSEMBLING THE
BLADE SYSTEM, ENSURE EACH PART IS REINSTALLED
CORRECTLY, AS DESCRIBED BELOW. IMPROPER ASSEMBLY
OF THE BLADE OR OTHER PARTS OF THE BLADE SYSTEM
MAY CAUSE SERIOUS INJURY.

DANGER: To reduce the risk of serious personal
injury, turn unit off, remove safety key, and remove
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
1. Cut a piece of 2" x 4" wood
(610 mm) to keep blade from turning when removing the
flange nut .
25

WARNING: Use gloves and proper eye protection. Turn the
mower on its side. Be careful of sharp edges of blade.
2. Position wood and unscrew flange nut counterclockwise
with a 18mm wrench
26
3. Remove square metal blade spacer
blade insulator and blade
28
blade fan should not be removed. Examine all pieces for
30
damage and replace if necessary.
4. Install sharpened or new (STZMW353) blade
shoulder of the blade fan as shown in Fig. K.
nOTE: When replacing sharpened or new blade on shoulder of
blade fan, make sure the "GRASS SIDE" on the blade will be
facing the ground when the mower is returned to its normal
upright position.
5. Install the plastic blade insulator
the raised lips on one side engage the edges of the blade.
6. Install the blade spacer
lips on the other side of the blade insulator. Be sure to align
the flats in the hole of the blade spacer with the flats of the
shaft, rotating the blade and blade insulator together as
necessary.
7. Position piece of wood to keep blade from turning as shown
in Fig. L. Install flange nut
blade spacer and securely tighten the blade
27
wrench .
26
Blade Sharpening
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A DULL
BLADE DOES NOT CUT GRASS CLEANLY.

WARNING: Use gloves and proper eye protection while
removing, sharpening, and installing blade. Ensure that
safety key and battery pack are removed.
Sharpening the blade twice during a mowing season is usually
sufficient under normal circumstances. Sand causes the blade
to dull quickly. If your lawn has sandy soil, more frequent
sharpening may be required. REPlACE BEnT OR DAMAgED
BlADE iMMEDiATElY.
When Sharpening the Blade:
• Make sure blade remains balanced.
• Sharpen blade at the original cutting angle.
(about 2 feet long)
24
as shown in Fig. J.
, square plastic
27
as shown in Fig. K. The
29
on
29
on the blade such that
28
so that it sits inside the raised
27
with the flange against the
25
29
English
with a
13