Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
SYMBOLS
Use dust mask. Dust which is
Use dust mask. Dust which is
©
©
injurious to health can be
injurious to health can be
generated when working on
generated when working on
wood and other materials.
wood and other materials.
RPM
Revolutions Per Minute
Revolutions Per Minute
Safety alert
Safety alert
min
min
Minutes (time)
Minutes (time)
S
S
Seconds (time)
Seconds (time)
Ø
Ø
Diameter (size of drill bits, grinding
Diameter (size of drill bits, grinding
wheels, etc.)
wheels, etc.)
UL Listing for Canada and U.S.
UL Listing for Canada and U.S.
n
n
No load speed (rotational speed at no
No load speed (rotational speed at no
0
0
load)
load)
0
0
Off position (zero speed, zero torque...)
Off position (zero speed, zero torque...)
Selector settings (speed, torque, or
Selector settings (speed, torque, or
1,2,3, ...
position settings. Higher number means
position settings. Higher number means
greater speed)
greater speed)
W
W
Watts
Watts
A
A
Amps
Amps
HZ
HZ
Hertz
Hertz
V
V
Volts
Volts
wood and other materials.
Disconnect the power cord from the power source before
RPM
making any adjustments or changing accessories. Preventive
Revolutions Per Minute
safety measures reduce the risk of starting the tool
DEFINITION OF SYMBOLS USED ON TOOL
accidentally.
Safety alert
min
Minutes (time)
FUNCTIONAL DESCRIPTION
S
the detent.
Seconds (time)
Cat. No:
Cat. No:
Ø
Diameter (size of drill bits, grinding
wheels, etc.)
3. Remove any accessories and adapter.
Voltage & Frequency:
Voltage & Frequency:
UL Listing for Canada and U.S.
n
Motor Power:
5. Place the accessory onto the tool and align the hole in the
Motor Power:
No load speed (rotational speed at no
0
load)
accessory with the cam of the tool.
No Load Speed:
No Load Speed:
8,000-16,000/min
0
Off position (zero speed, zero torque...)
6. Press the quick release lever back into place.
Selector settings (speed, torque, or
7. Check that the accessory is seated securely. Accessories
Oscillating Angle:
Oscillating Angle:
1,2,3, ...
position settings. Higher number means
greater speed)
place may come loose during operation, thereby putting
W
Watts
you at risk.
A
A
Gear Box
A
Amps
B
B
HZ
Hertz
C
C
On/Off Switch
V
Volts
B
D
D
Speed Control Dial
C
E
E
Draw-in Bolt
F
F
Air Vent
8
8
A
G
G
Air Vent
H
H
Tool Hanger
E
Disconnect the power cord from the power source before
making any adjustments or changing accessories. Preventive
safety measures reduce the risk of starting the tool
accidentally.
the detent.
OSC9500-A
OSC9500-A
3. Remove any accessories and adapter.
120V/60Hz
120V/60Hz
5. Place the accessory onto the tool and align the hole in the
4 A
4 A
accessory with the cam of the tool.
8,000-16,000/min
6. Press the quick release lever back into place.
7. Check that the accessory is seated securely. Accessories
5 Degrees
5 Degrees
place may come loose during operation, thereby putting
you at risk.
Gear Box
Lever
Lever
On/Off Switch
D
Speed Control Dial
Draw-in Bolt
Air Vent
G
Air Vent
F
Tool Hanger
3. Remove any accessories and ada
Voltage & Frequency:
120V/60Hz
Motor Power:
5. Place the accessory onto the tool
4 A
accessory with the cam of the too
No Load Speed:
8,000-16,000/min
6. Press the quick release lever back
WARNING! Only use accessories
7. Check that the accessory is seated
Oscillating Angle:
5 Degrees
specifically recommended for this tool.
Others may be hazardous
place may come loose during op
you at risk.
A
Gear Box
B
Lever
C
On/Off Switch
D
Speed Control Dial
E
Draw-in Bolt
F
Air Vent
8
G
Air Vent
H
Tool Hanger
H
WARNING
WARNI
WARNING
WARNI
WARNING
WARNI
OSHA complia
OSHA c
WARNING
WARNI
the power sou
the pow
7
Publicidad
Tabla de contenido
