Daspi EPRE Manual De Instrucciones página 3

1 • saFety rules Warning: Any repairing, fitting or adjustment made from people not qualified is strictly forbidden and in order to avoid any possible accident, all necessary
gb
precautions must been taken (ex: switch off the power supply as well as disconnect batteries). Daspi is not responsible for possible damages or injuries to people, objects or
animals caused by any unauthorized modification of product. Do not install this product into an explosive place. Keep scrupulously this booklet and include it into the main
user manual in a suitable place well known by all the interested people.
2 • model The control panel EPRE has been designed for driving 1 operator for sliding gates mod. MAX and it has an electronic clutch. Daspi is not responsible for any different use of
control panel EPRE.
3 • list oF maiN compoNeNts
F1 Net and motor protection's fuse T5A
Accessories protection's fuse 2A
F2
Terminal for power supply 230 Vac 50-60 Hz
Jp1
Terminal for motor and flashing light
Jp2
Dip switch for control panel set up
sW1
leeds (they turN oN aFter poWer supply has beeN coNNected) Will shoW coNtrol paNel eNtraNces coNNectioNs
dl1 Always off, it switches on by control START
dl2 Always off, it switches on by control of pedestrian system
dl3 Flashing when transmitters programming
dl4 Always on, it switches off by STOP
dl10 It switches on when motor starts. When flashing, it means an anomaly on
its functions
Check again the connections and the devices if the above led don't correspond.
4 • coNtrol paNel programmiNg aNd adJustiNg The programming of DIP SWITCHES SW1 must be made with control panel switched off.
IMPORTANT: Every time you set up a new feature on the DIP, Cut off power supply and than switch it on again andwait at least 5-6 sec. before giving any control to the gate.
1 Residential system desactivated. During opening it accept any control START.
Disabled
2
Photocells working only while closing. They stop and re-open
3
4 Pre-flashing deactivated
5 • poWer adJustiNg by trimmer poWer (electroNic clutch) Any adjust of electronic clutch must be made from professional people in order to avoid any possible accident and
reduce all crashing risks. • rotate the trimmer POWER to increase or to decrease the
to the actual rules.. • Power measurements on the leaves, have to be made following to actual norms.. • Check periodically the clutch system in order to guarantee always a full safety.
6 • WorKiNg time adJustiNg The time of work is automatically calculated and
7 • automatic shuttiNg Adjustable from 0 to 120 second through the trimmer SENS. If you set the trimmer at the minimum, the automatic shutting is off.
8 • hoW to set traNsmitters codes (max 16 codes oN start aNd 16 codes oN ped)
Control START:
To set the code on the control START press and release the button SET, the led DL3 will start flashing slowly. Send now the signal pressing the button on the remote control you want to
set in; the led on the panel will turn off showing the code has been accepted.
if the memory is full or the code is already memorized the led DL3 it quickly flashes
Control PED:
To set the code on the control PED (pedestrian) press and release the button SET, press again and release the button SET, the led DL3 will start flashing. Send now the signal pressing the
button on the remote control you want to set in; the led on the panel will turn off showing the code has been accepted.
if the memory is full or the code is already memorized the led DL3 it quickly flashes
9 • hoW to erase all codes From the receiver press and maintain pressed for more than 10 seconds the
10 • termiNals descriptioNs Join with a bridge the N.c. (normally closed) entrances you don't use. If you are using more contacts N.C. on same entrance, they must be connected
in set. If you are using more contacts N.O. on same entrance, they must be connected in parallel
1 Entrance main power supply
2 230Vac 50Hz
3 Entrance flashing light 230Vac max 25W
4
5 Entrance motor (5 common, 6 open, 7 close).
6 Connect capacitor on 6-7
7
8 Entrance limit switch closing (contact N.C.)
9
8 Entrance limit switch opening (contact N.C.)
10
8 Entrance for photocells (contact N.C.)
11
it is possible to add a "timer" connecting on start entrance (16-17) a timer in order to open and close the gate at certain hours.
11 • testiNg: to be made With gate iN halF opeN positioN aNd oNly aFter iNstalliNg the required saFety devices provided From by laW iN order to reduce
aNy risK. Check all motor connections remembering that first operation made by the control panel is an opening. If gate closes invert connections 6-7 • Check the limit switches function
moving manually the spring • Be sure that electronic clutch has been adjusted according to actual norms and after all the safety measurements • Verify whether all safety devices installed
are working properly in order to reduce any risk. • All people in charge of the automation must be trained about the safety devices, controls and dangerousness of system. Fill up technical
booklet and carry out the obligations required from actual rules and norms
oFF
torque
lasts
Jp3 Terminal for accessories – devices
Terminal for antenna and accessories
Jp4
Button for transmitter's programming
set
Receiver incorporated
J3
dl5 Always on, it switches off by control of safety edge
dl6 Always on, it switches off by control of photocells
dl7 Always on, it switches off by control limit-switches opening
dl8 Always on, it switches off by control limit-switches closing
During opening the control panel doesn't accept any other control (Residential
system)
Immediate re-closing after disengaging the two photocells
Photocells working also during opening: the activation of photocell stops the
gate. As soon as the obstacle is removed, the gate continues opening
Pre-flashing activated 2.5 sec before start
of the motor. • Check that leaves on movement can be stopped at any time easily according
10 seconds more than the run of the gate.
Set, all the remote controls are cancelled.
button
8 Entrance for safety edge (contact N.C.)
12
13 Entrance button STOP (contact N.C.). It stops any movement and avoid for
14 that operation the automatic shutting
13 Entrance button PEDESTRIAN system (contact N.O.) (it opens the
15 gates for approx. 1mt only)
16 Entrance button START open-stop-close (contact N.O.)
17
18 Entrance 24Vac for accessories
19
21
Shield
20 Hot pole antenna
oN