Publicidad
Application
The thermostatic valve is designed for use with hot water
supplied from pressurized storage heaters and offer the
highest temperature accuracy when used in this way.
The thermostatic valve cannot be used in conjunction with
low-pressure storage heaters (displacement water heaters).
• Do not loose the adaptor (C) mounted on the fitting
template. You need this adaptor and the fastening set (C1)
(keep in the bag) for a few trims, see page 2.
• The adaptor (A) and the stop ring (B) are pre-mounted on
the valve. These parts will be used for several trims too, see
page 2.
• Please be careful that this instruction is present for the final
installation- you can have different rough in valves with
different installtion steps!
Specification
• Concealed single handle thermostatic valve
• Integral service stops
• Integral check valves prevent cross flow
• Thermostatic cartridge automatically adjusts to inlet
temperature and pressure fluctuations
• Cartridge restricts hot water supply should the cold pressure
fail, to prevent scalding
• Flow pressure:
- min
- recommended
greater than 72.5 psi, fit pressure reducing valve
• Max. operating pressure
• Max. test pressure
• Flow rate at 45 psi flow pressure
• Temperature
- max. (hot water inlet)
• Back-to-back installation is possible by reversing the
cartridge-holder.
(see back-to-back installation instructions)
• Water connection:
Rough-in installation
1. Prepare wall for rough-in valve.
2. Observe the installation depth in accordance with the
instructions given on the fitting template, see fig. [1] and [3].
H = Face of tiles
G = Front face of fitting template
F = Resting point for spirit level
3. Align the mixer horizontally, vertically and parallel to the wall,
see fig. [4] (place a spirit level on the cams or face of the
fitting template).
4. Install concealed thermostatic valve in the wall and connect
pipes.
Permissible tolerances are given in the dimensional
drawing, see page 1.
English
IMPORTANT
A shut-off device must be installed after the mixed water outlet
of concealed thermostatic valve.
It is not necessary to remove the cartridge from the valve
during normal soldering connection.
This valve has no by-pass annulus and therefore when
used with diverter spout a twin ell must be used and the
top outlet plugged.
Check connections for leakage.
Flush piping system prior and after installation of faucet
thoroughly!
Back-to-back installation
1. Identify valve with hot/cold reversed supply.
2. Unscrew screws (E) to remove adaptor (C) and finish wall
3. Remove the adaptor (A), see Fig. [2].
4. Remove screws (J), screw (K) and remove unit (L), see
5. The valve body is equipped with service stop valves (I),
6. Remove the four cover screws (M) and remove the valve
20 psi
7. Pull the cartridge-holder (Q) straight out of the valve body.
20 – 72.5 psi
125 psi
500 psi
61 L/min or 16 gpm
180 °F
8. When correctly engaged the cartridge holder will not
9. Take care not to damage inlet O-ring (R).
10. If the the O-ring (P) is not on the valve cover (N) re-install
cold - RH
hot - LH
11. Seat the valve cover (N) with assembled cartridge in the
12. Open service stops valves (I) by turning the screws
13. Re-install all parts and be sure that the adapter (C) will be
Plaster and tile the wall
Do not remove the fitting template before final installation.
Replacement parts, see page 1 (* = special accessories).
template (D), see Fig. [1].
Fig. [5].
close the hot and cold water supplies by turning the screws
vertically. Otherwise shut off the supply at the nearest
source.
cover (N) as assembled unit with the O-ring (P).
Rotate the cartridge-holder (Q) 180°. Place it into the valve
body. Note position of hot "H" and cold "C" markings on the
cartridge-holder: "H" hot will now be on the right and "C"
cold on the left. Make sure when sliding cartridge-
holder (Q) into the body that the cartridge holder fits into
the positioning grooves (S) of the body, see Fig. [6].
rotate.
and make sure the surface of the valve cover and the O-
ring (P) are both clean, see Fig. [5].
cartridge-holder (Q). Do not pinch the O-ring (P). The
assembly should fit together with a minimum of pressing
force. Install the cover screws (M). Tighten lightly in a
diagonal pattern, then tighten firmly.
horizontally. Otherwise open the supply at the nearest
source.
on the fitting template, see Fig. [1].
4
Publicidad
