Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
17.
Orient cover support collar [13] as required by removing and reinstalling screws [14]. Lap joint in collar defines the
hinge location of the cover, SEE FIGURES D & E.
18.
Install finished flooring to within 1/8 inch [3.2 mm] of cover support collar [13]. FOR CERAMIC TILE - DO NOT GROUT
BETWEEN THE SUPPORT COLLAR AND TILE.
19.
Adjust height of cover support collar flush to just below the finished floor. Cover support collar is adjustable for
finished floors of 0 inches to .25 inches [0.0 - 6.4 mm] thick. Tighten mounting screws [14] to 10 - 15 lbs-in torque
[1.1 - 1.7 N-m]. For thicker floor finishes use accessory collars (CFB8RCVRRx), sold separately.
20.
Seal the gap around the cover support collar [13] with a continuous bead of electrical grade type RTV silicone sealant,
SEE FIGURE F.
21.
Use the provided floor gasket or apply a 1/4 inch [6.3 mm] thick continuous bead of electrical type of RTV silicon
sealant compound fully around the perimeter on the underside of the flange [15].
22.
Attach flange [15] to the cover support collar [14] using #8-32 flat head screws [16] provided with the cover.
LAP JOINT
14
13
(HINGE SIDE)
LAP JOINT
(HINGE SIDE)
FIGURE
E
FIGURE
13
16
FIGURE
D
15
SEAL ALL AROUND
F
CFB10GS1R8ADAPT ROUND COVER ADAPTER FOR 10G RECESSED
CONCRETE FLOOR BOX Installation Instructions
CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing or servicing.
NOTICE: For installation by a qualified electrician in accordance with all national and local electrical codes,
communications standards, the following instructions and any instructions included with individual devices.
NOTICE: Insure data/communications circuits are separated from lighting/power circuits in accordance with the NEC and
CE Code requirements.
Use with CFB10G55, or CFB10G55CR floor boxes.
Use with CFBS1R8CVRxx series round covers.
BEFORE CONCRETE POUR, SEE FIGURES A & B
1.
Remove four #8-32 flat head screws [1] from top corners of floor box assembly and discard.
2.
Remove mounting plate [2] from the box.
3.
REMOVE AND DISCARD PLASTIC [3] AND METAL [4] COVERS ATTACHED TO THE MOUNTING PLATE [2].
14
4.
Install leveling screws [5] as shown in FIGURE A.
5.
Make conduit connections in accordance with application and applicable electric codes.
3
4
1
2
6
5
Wiring Device - Kellems
Hubbell Incorporated (Delaware)
40 Waterview Dr.
Shelton, CT 06484
1-800-288-6000
www.hubbell-wiring.com
PD2598
04/14
FIGURE
A
ENGLISH
Publicidad
Manuales relacionados para Hubbell CFB10GS1R8ADAPT
Resumen de contenidos para Hubbell CFB10GS1R8ADAPT
- Página 1 CFB10GS1R8ADAPT ROUND COVER ADAPTER FOR 10G RECESSED Orient cover support collar [13] as required by removing and reinstalling screws [14]. Lap joint in collar defines the hinge location of the cover, SEE FIGURES D & E. CONCRETE FLOOR BOX Installation Instructions Install finished flooring to within 1/8 inch [3.2 mm] of cover support collar [13].
- Página 2 For feed-thru wiring, remove non-metallic dividers [6] as necessary. AFTER CONCRETE POUR, SEE FIGURES C, D, E, & F Reposition mounting plate [2] in floor box. Install adapter [7] on top of the mounting plate [2]. Secure using #8-32 Locate floor box, remove three screws [10] and remove temporary concrete cover [9]. CAUTION: Temporary concrete pan head screws [8] supplied with adapter.
- Página 3 (consulter les FIGURES D et E). Installer le recouvrement de sol moins de 3,2 mm du collier de soutien du couvercle [13]. POUR LES CARREAUX DE CFB10GS1R8ADAPT Directives de montage FRAN AIS C RAMIQUE - NE PAS METTRE DE COULIS ENTRE LE COLLIER DE SOUTIEN ET LA C RAMIQUE.
- Página 4 Pour le c blage en travers e, enlever les cloisons non m talliques [6] au besoin. APR S LA COUL E DU B TON, CONSULTER LES FIGURES C, D, E ET F Repositionner la plaque de montage [2] dans la bo te de plancher. Monter l'adaptateur [7] par-dessus la plaque de Localiser la bo te de plancher, retirer les trois vis [10] et le couvercle temporaire [9].
- Página 5 FIGURA Wiring Device - Kellems HUBBELL DE M XICO garantiza este producto, de estar libre de defectos en materiales y mano de obra por un a o a partir de su compra. Hubbell reparar o reemplazar el Hubbell Incorporated (Delaware) art culo a su juicio en un plazo de 60 d as.
- Página 6 Para cableado atravesado, retirar los divisores no met licos [6] seg n la necesidad. DESPU S DEL COLADO DEL HORMIG N, VER FIGURAS C, D, E, & F Volver a posicionar la placa de montaje [2] en la caja para piso. Instalar el adaptador [7] encima de la placa de Ubicar la caja para piso, retirar tres tornillos [10] y la tapa temporal para hormig n [9].