Starting Operation - Würth S 12-A Traducción Del Manual De Instrucciones De Servicio Original

página de 178

/ 178
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

OBJ_BUCH-1884-003.book Page 15 Wednesday, June 22, 2016 8:11 AM

The vibration level given in this information sheet has been

measured in accordance with a standardised test given in

EN 60745 and may be used to compare one tool with

another. It may be used for a preliminary assessment of expo-

sure.

The declared vibration emission level represents the main

applications of the tool. However if the tool is used for differ-

ent applications, with different accessories or insertion tools or

is poorly maintained, the vibration emission may differ. This

may significantly increase the exposure level over the total

working period.

An estimation of the level of exposure to vibration should also

take into account the times when the tool is switched off or

when it is running but not actually doing the job. This may sig-

nificantly reduce the exposure level over the total working

period.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and the

accessories, keep the hands warm, organisation of work pat-

terns.

EC-Declaration of Conformity

We declare under our sole responsibility that the product

described under "Tool Specifications" complies with all

applicable provisions of the directives 2009/125/EC

(Regulation 1194/2012), 2011/65/EU, 2014/30/EU,

2006/42/EC including their amendments and is in conform-

ity with the following standards: EN 60745-1,

EN 60745-2-2, EN 50581.

Technical file (2006/42/EC) at:

Adolf Würth GmbH & Co. KG, Abt. PPT

Reinhold-Würth-Straße 12–17

74653 Künzelsau

GERMANY

www.wuerth.de

Frank Wolpert

Dr.-Ing. Siegfried Beichter

General Manager

Künzelsau: 13.06.2016

Removing the Battery (see figure A)

Note: The battery supplied is partially charged. To ensure

full capacity of the battery, completely charge the battery in

the battery charger before using your power tool for the first

time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging procedure

does not damage the battery.

The lithium-ion battery is protected against deep discharging

by the "Electronic Cell Protection (ECP)". When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch

after the machine has been automatically

switched off. The battery can be damaged.

To remove the battery 7 press the unlocking buttons 6 and

pull out the battery downwards. Do not exert any force.

Observe the notes for disposal.

Changing the Tool (see figure B)

 Before any work on the machine itself (e. g.

maintenance, tool change, etc.) as well as dur-

ing transport and storage, remove the battery

from the power tool. There is danger of injury when

unintentionally actuating the On/Off switch.

Inserting

Pull the locking sleeve 3 toward the front and then push the

insert tool to the stop into the tool holder 2. The insert tool is

automatically locked.

Removing

Pull the locking sleeve 3 forward and remove the insert tool.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one's

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment addi-

tives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

• Provide for good ventilation of the working place.

• It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-

rials to be worked.

 Prevent dust accumulation at the workplace.

Dust can easily ignite.