DWT HB03-110 B Manual Del Usuario página 18

• Blade for plane shall be correctly installed and
used according to instructions provided by the
manufacturer. Attention shall be paid to the size
which must match the press plate to ensure that no
mechanical friction occurs between the blade for plane
and press plate during operation after installation� After
installation, the switch shall be started at a safe posi-
tion and the tool shall operate for 30 seconds� In case
of serious vibration or other problem, the operation
shall be stopped and arrangement shall be made for
maintenance�
• Machined workpiece shall be reliably fastened
and clamped with fixture or bench clamp to the
greatest extent.
• The fingers shall not be put on switch button to
avoid turning on the tool unconsciously when the
tool moves.
• The power tool shall be started before being
placed on material surface for processing. When
planing operation is carried out, inspection shall be
carried out to see whether any foreign matter is hid-
den in the workpiece, for example, nails and screws�
Any foreign matter discovered shall be removed before
operation�
• When the power tool is used, it must be ensured
that power lines are placed behind the frame far
away from working head. Power lines or damaged
tool shall not be used� If the power lines are dam-
aged during work, you shall not touch damaged power
lines; instead, you shall promptly pull out the plug and
change the power lines�
• The power tool shall be shut off before being
put down. After cutting off the power, the power tool
could be put down only after work head of the tool is
completely static� At that time, you could not touch
the blade for plane with hands� Similarly, the blade for
place will be very hot during operation; therefore, you
shall not touch it with hands before it is cooled�
• If dust harmful to health, combustible or explo-
sive dust is generated during work, appropriate
safety measures shall be taken. For example: waste
dust that may cause cancer� During work, you should
use equipment for removal of waste dust and sweeps
and wear dust mask�
• The workplace shall be kept clean. After mixing,
the materials may be of high risk.
• Since asbestos may cause cancer, materials
containing asbestos shall not be processed.
• The power tool could be put down only after the
blades is completely static. The blades installed on
the power tool might be caught thus making it impos-
sible to control power tool�
• The power tool with damaged cables shall not be
used. In case the power lines are damaged or broken
during work, you should not touch the power lines; in-
stead, you should pull out the plug immediately� Dam-
aged power lines may cause electric shock�
• The power tool shall be started before it is pro-
cessed in the workpiece. If the blade is stuck in the
workpiece, the power tool will rebound�
• The power tool shall not be operated by children.
• Only sharp blades could be used.
• During work, the power lines shall be placed be-
hind the power tool.
• During work, you should firmly grip the power
tool and stand stably.
• During work, the base plate must be affixed to
surface of the material.
• When planing work is carried out, the blade shall
not get in touch with metal, nail or screw.
• When the power tool is operating, the fingers
shall not be placed into discharge port for shav-
ings.
Notice the power voltage: in power connection, you
must confirm that if the power voltage is the same to
the voltage marked in the tool's data plate� If the power
voltage is higher than the appropriate voltage, the acci-
dents will be resulted to the operators, and at the same
time, the tool will be destroyed� Therefore, if the power
voltage has not been confirmed, then you shall never
plug in arbitrarily� On the contrary, when the power
voltage is lower than the required voltage, the motor
will be damaged�
Following symbols are used in the operation manual,
please remember their meanings� Correct interpreta-
tion of the symbols will allow correct and safe use of
the power tool�
Symbol
English
18
Symbols used in
the manual
Meaning
Power planer
Sections marked gray - soft
grip (with insulated surface)�
Serial number sticker:
HB ��� - model;
XX - date of manufacture;
XXXXXXX - serial number�
Read all safety regulations
and instructions�
Wear safety goggles�
Wear ear protectors�
Wear a dust mask�
Disconnect the power tool
from the mains before instal-
lation or adjustment�
Movement direction�