Setting Up Your Tv - Insignia NS-LCD15 Guia Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

#
Button
Description
17
MENU
Press to open the on-screen menu.
18
FAVORITE
Press to toggle the Favorite/Normal
mode. See "Setting up the channel list"
on page 8 for more information.
19
VOL + or –
Press to adjust the volume up or down.
20
Use with the 0-9 number buttons and
ENTER key to select digital channels.
21
[Number buttons] Press to enter channel numbers.
In the on-screen menu, press to enter
your parental control's password.
22
COMP
Press to select Component source
mode.
23
VIDEO
Press to toggle between S-Video and
Composite source modes.
24
INPUT
Press to select the video input signal
source.
25
DISPLAY
Press to display status information.
Using the remote control
To use the remote control:
Point the remote control towards the remote
sensor on the front of your TV.
Notes
• Do not expose the remote control to shock or
liquids.
• Do not use the remote control in an area with
high humidity.
• Do not place the remote control in direct
sunlight.
• Do not place objects, such as furniture,
between the remote control and the remote
sensor.
• The remote control may not work if direct
sunlight or bright light shines on the remote
sensor. Either move your TV or change the
angle at which you use the remote control.

Setting up your TV

Installing remote control batteries
To install the remote control batteries:
1 Remove the battery cover.
2 Insert two AAA batteries into the battery
compartment. Make sure that you match the
+ and – symbols on the batteries with the +
and – symbols in the battery compartment.
3 Replace the cover.
6
Notes
Connecting your TV to a power outlet
To connect your TV to a power outlet:
Notes
Connecting an outside antenna
Antenna cables come in two types: 75 ohm and
300 ohm.
If your antenna cable has a 75 ohm
connector, connect the cable to the coaxial
jack on the back of your TV.
If your antenna cable has a 300 ohm
connector, connect the cable to a
300-75 ohm adapter (not included), connect
the adapter to a 75 ohm cable, then connect
the other end of the 75 ohm connector to the
coaxial jack on the back of your TV.
Connecting cable TV
Your TV has a 75 ohm jack for connecting cable
TV.
Some cable TV providers scramble the signals
for "premium" (pay) channels. To view these
channels, you need a converter/descrambler
box.
If you do not have a converter/descrambler box,
you can connect your cable TV directly to your
TV. If you have a converter/descrambler box, you
can connect your cable TV using an RF switch
(not supplied). For more information about
connecting a converter/descramble box, contact
your cable TV provider.
To connect cable TV without a
converter/descrambler box:
1 Connect one end of a 75 ohm cable to the
coaxial jack on the back of your TV.
2 Connect the other end of the cable to the
cable TV wall outlet.
www.insignia-products.com
Insignia NS-LCD15 15" LCD TV
• Do not mix batteries of different types.
• Do not mix old and new batteries.
• Remove batteries when the charge is depleted.
• Battery chemicals can cause a rash. If the
batteries leak, clean the battery compartment
with a cloth. If chemicals touch your skin, wash
immediately.
• If the remote control is not going to be used for
an extended period of time, remove the
batteries.
Plug the power cord into a power outlet.
• Make sure that you use the correct type of
power. See the label on your TV.
• If you do not intend to use your TV for an
extended period of time, unplug the power cord
from the power outlet.
75 ohm cable
300 ohm cable

Publicidad

Tabla de contenido
loading

Tabla de contenido