Before Use; During Use; After Use - Skil F015566 Serie Manual Original

ADDITIONAL SAFETY WARNINGS
GENERAL
• This tool should not be used by people under the age of
16 years
• This tool is not suitable for wet cutting
• Always disconnect plug from power source before
making any adjustment or changing any accessory
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• Do not work materials containing asbestos (asbestos
is considered carcinogenic)
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classified as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Only use a saw table provided with a switch that prevents
restarting of the motor after interruption of voltage
• Only use a saw table provided with a kerf guide
ACCESSORIES
• SKIL can assure flawless functioning of the tool only
when original accessories are used
• Use only saw blades that correspond with the
characteristic data given in these operation instructions
and that are tested and marked in accordance with EN
847-1
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
• Use only saw blades with a minimum diameter of
184 mm, a maximum diameter of 184 mm and a
spindle hole of 16 mm
• Never use saw blades made of high speed steel (HSS)
• Never use grinding/cutting discs with this tool

BEFORE USE

• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Remove all obstacles on top of as well as underneath the
cutting path before you start cutting
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Use suitable detectors to find hidden utility lines or
call the local utility company for assistance (contact
with electric lines can lead to fire or electrical shock;
damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)

DURING USE

• The noise level when working can exceed 85 dB(A); wear
ear protection
• Never use the tool without the original protection guard
system
• Do not attempt to cut extremely small workpieces
• Do not work overhead with the tool
• In case of jamming or electrical or mechanical
malfunction, immediately switch off the tool and
disconnect the plug
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug

AFTER USE

• When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
• After switching off your circular saw, never stop the
rotation of the saw blade by a lateral force applied against
it
EXPLANATION OF SYmBOLS ON TOOL
2 Read the instruction manual before use
3 Double insulation (no earth wire required)
4 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Mounting saw blade 5
! disconnect the plug
- take hex key A from storage B
- push spindle-lock button C and hold it while you
remove blade bolt D with hex key
! push spindle-lock button C only when tool is at a
standstill
- release spindle-lock button C
- remove flange E
- open lower guard F with lever G and hold it while you
mount saw blade with saw teeth and arrow printed on
saw blade pointing in same direction as arrow on
upper guard
- release lower guard F
- mount flange E
! make sure that clamping surfaces H of flanges
are perfectly clean and face the blade
- push spindle-lock button C and hold it while you
tighten blade bolt with hex key 1/8 turn past finger tight
(ensures slippage of saw blade when it encounters
excessive resistance thus reducing motor overload
and saw kickback)
- release spindle-lock button C
• Adjusting cutting depth (0-65 mm) 6
- for an optimal quality cut the saw blade should not
extend more than 3 mm below the workpiece
- loosen knob J
- raise/lower foot K until desired cutting depth is set on
scale using indicator L
- tighten knob J
12