Before Use; Electrical Safety; Personal Safety - Skil 4950 Manual Original

c) Disconnect the plug from the power source and/or
remove the battery pack, if detachable, from the
power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR RECIPROCATING SAWS
ACCESSORIES
• SKIL can assure flawless functioning of the tool only
when the correct accessories are used which can be
obtained from your SKIL dealer
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool

BEFORE USE

• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working

ELECTRICAL SAFETY

• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord (cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock)
• Use suitable detectors to find hidden utility lines or
call the local utility company for assistance (contact
with electric lines can lead to fire or electrical shock;
damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
All manuals and user guides at all-guides.com

PERSONAL SAFETY

• In case of electrical or mechanical malfunction,
• This tool should not be used by people under the age of
• Do not work materials containing asbestos (asbestos
• Dust from material such as paint containing lead, some
• Certain kinds of dust are classified as carcinogenic (such
• Follow the dust-related national requirements for the
• Keep hands away from cutting area and the blade;
• Do not reach underneath the workpiece (the proximity
• Never hold piece being cut in your hands or across
• Use clamps or another practical way to secure and
• Do not use a dull or damaged blade (bent blades can
• Keep hands away from between the tool housing
• Ensure that blade clamp D 2 is tight before making a
• Use protective gloves when removing the blade
• Wear protective glasses and hearing protection
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
• If for any reason the old plug is cut off the cord of this tool,
USE
• On/off 6
• Speed control
9
immediately switch off the tool and disconnect the plug
16 years
is considered carcinogenic)
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when
connectable
materials you want to work with
keep your second hand on barrel grip H 2 (if both
hands are holding the saw, they can not be cut by the
blade)
of the blade to your hand is hidden from your sight)
your leg (it is important to support the work properly to
minimise body exposure, blade binding, or loss of
control)
support the workpiece to a stable platform (holding
the workpiece by hand or against your body leaves it
unstable and may lead to loss of control)
break easily or cause kickback)
and blade clamp D 2 (the blade clamp can pinch your
fingers)
cut (a loose clamp may cause the tool or blade to slip
with loss of control as a result)
from the tool (the saw blade may be hot after prolonged
use)
material
in the cord of this tool to the earth terminal of the plug
it must be disposed of safely and not left unattended
With wheel C 2 the sawing speed can be adjusted from
low to high (6 positions)