Axis M30-V Serie Guia De Instalacion página 14

English
Safety Information
Read through this Installation Guide carefully before
installing the product. Keep the Installation Guide
for future reference.
Hazard Levels
DANGER
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
NO NO TICE NO TICE TICE
Indicates a situation which, if not avoided, could
result in damage to property.
Other Message Levels
Important
Indicates significant information which is essential
for the product to function correctly.
Note
Indicates useful information which helps in getting
the most out of the product.
Safety Instructions
NO NO TICE NO TICE TICE
•
The Axis product shall be used in compliance
with local laws and regulations.
•
To use the Axis product outdoors, or in similar
environments, it shall be installed in an approved
outdoor housing.
•
Store the Axis product in a dry and ventilated
environment.
•
Avoid exposing the Axis product to shocks or
heavy pressure.
•
Do not install the product on unstable brackets,
surfaces or walls.
•
Use only applicable tools when installing the Axis
product. Using excessive force with power tools
could cause damage to the product.
•
Do not use chemicals, caustic agents, or aerosol
cleaners.
•
Use a clean cloth dampened with pure water for
cleaning.
•
Use only accessories that comply with the
technical specification of the product. These can
be provided by Axis or a third party.
•
Use only spare parts provided by or recommended
by Axis.
•
Do not attempt to repair the product yourself.
Contact Axis support or your Axis reseller for
service matters.
•
The power supply shall be plugged in to a socket
outlet installed near the product and shall be
easily accessible.
•
Use a limited power source (LPS) with either a
rated output power limited to ≤100 W or a rated
output current limited to ≤5 A.
Transportation
NO TICE TICE
NO NO TICE
•
When transporting the Axis product, use the
original packaging or equivalent to prevent
damage to the product.
Battery
The Axis product uses a 3.0 V CR2032 lithium battery
as the power supply for its internal real-time clock
(RTC). Under normal conditions this battery will last
for a minimum of five years.
Low battery power affects the operation of the RTC,
causing it to reset at every power-up. When the
battery needs replacing, a log message will appear
in the product's server report. For more information
about the server report, see the product´s setup pages
or contact Axis support.
The battery should not be replaced unless required,
but if the battery does need replacing, contact Axis
support at www.axis.com/techsup for assistance.
Lithium coin cell 3.0 V batteries contain
1,2-dimethoxyethane; ethylene glycol dimethyl ether
(EGDME), CAS no. 110-71-4.
WARNING
•
Risk of explosion if the battery is incorrectly
replaced.
•
Replace only with an identical battery or a
battery which is recommended by Axis.
•
Dispose of used batteries according to local
regulations or the battery manufacturer's
instructions.
Dome Cover
NO TICE TICE
NO NO TICE
•
Be careful not to scratch, damage or leave
fingerprints on the dome cover because this
could decrease image quality. If possible, keep
the protective plastic on the dome cover until
the installation is complete.
•
Do not clean a dome cover that looks clean to
the eye and never polish the surface. Excessive
cleaning could damage the surface.
•
For general cleaning of the dome cover it is
recommended to use a non-abrasive, solvent-free
neutral soap or detergent mixed with pure water
and a soft, clean cloth. Rinse well with pure
lukewarm water. Dry with a soft, clean cloth to
prevent water spotting.