Monacor International JTS RU-8012DB/5 Manual De Instrucciones página 12

2-Channel Diversity UHF Receiver
for two transmitters RU-850... / 5
These instructions are intended for users without
any specific technical knowledge Please read the
instructions carefully prior to operation and keep
them for later reference
The operating elements and connections de-
scribed can be found on page 3
Contents
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2 Safety Notes . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 .1 Matching transmitters . . . . . . . . . . . . . . . . . . . 14
3 .2 Conformity and approval . . . . . . . . . . . . . . . . . 14
4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Configuring the System via the Menus . . . 15
5 .1 Menu section RX (receiver unit) . . . . . . . . . . . . 15
5 .1 .1 Selecting a frequency from a group . . . . . . . . 15
5 .1 .2 Setting the frequency directly . . . . . . . . . . . . 15
5 .1 .3 Activating / Deactivating the scan function . . . 16
5 .1 .4 Activating / Deactivating the attenuation
for the XLR output . . . . . . . . . . . . . . . . . . . . . 16
5 .1 .5 Setting the squelch value . . . . . . . . . . . . . . . . 16
5 .2 Menu section TX (transmitter) . . . . . . . . . . . . . . 16
5 .2 .1 Activating / Deactivating the attenuation
for the microphone input . . . . . . . . . . . . . . . . 16
5 .2 .2 Adjusting the audio sensitivity . . . . . . . . . . . . 16
5 .2 .3 Activating automatic switch-off . . . . . . . . . . . 16
5 .2 .4 Adjusting the transmission power . . . . . . . . . 17
5 .2 .5 Configuring the REMOSET function . . . . . . . . 17
6 Adjusting the Volume . . . . . . . . . . . . . . . . . 17
7 Activating / Deactivating the Key Lock . . . . 17
8 Establishing a Transmission Path . . . . . . . . 18
8 .1 Function
(synchronizing receiver unit and transmitter) . . . 18
9 Specifications . . . . . . . . . . . . . . . . . . . . . . . . 19
9 .1 Groups and channels (frequencies in MHz) . . . 19
12
1 Overview
for receiver unit 1 (RX1)
for receiver unit 2 (RX2)
1 Display (left: receiver unit 2; right: receiver
unit 1)
Indication Meaning
... MHz Radio frequency
G ... CH ... Group number and channel number
RF Strength of the radio signal received
AF Volume of the audio signal received
Diversity indication A or B: to show
which of the antennas receives the
radio signal of the higher quality
Battery symbol: to indicate the battery
status of the transmitter in multiple
levels
The receiver unit is muted:
- when no radio signal is received or
MUTE
when the radio signal received is poor
- when the transmitter is muted
Level of the corresponding XLR output (9)
ATT .ON
attenuated by 20 dB
Note: When the batteries of the transmitter are
almost discharged, the display backlight will change
to red and the battery symbol will start flashing
2 For each receiver unit: button
transfer settings to the transmitter via ultra-
sound: ☞ chapter 8 1
3 For each receiver unit: buttons SET,
SET to call up the menu: keep the button
pressed for 2 seconds
within the menu: to select the menu
items and to save a changed setting
, within the menu: to change a setting
 
outside of the menu: to adjust the
volume
The menu structure can be found in fig 1
on page 2 (as way of an example for receiver
unit 2)
4 Receiving antennas
5 Transmitter section for ultrasonic transmission
6 Button to activate /deactivate the key lock
(keep the button pressed for 2 seconds)
to
,
 