carquest professional lifting 3202 Manual Del Usuario

OWNER/USER RESPONSIBILITY
The owner and/or user must have a thorough understanding of
the manufacturer's operating instructions and warnings before
using this jack. Personnel involved in the use and operation
of equipment shall be careful, competent, trained, and quali-
fied in the safe operation of the equipment and its proper use
when servicing motor vehicles and their components. Warning
information should be emphasized and understood.
If the operator is not fluent in English, the manufacturer's
instructions and warnings shall be read to and discussed
with the operator in the operator's native language by the
purchaser/owner, making sure that the operator comprehends
its contents.
Owner and/or user must study and maintain for future
reference the manufacturer's instructions. Owner and/or user is
responsible for keeping all warning labels and instruction
manuals legible and intact. Replacement labels and literature
are available from the manufacturer.
IMPORTANT! BEFORE USING THIS JACK:
The breather located below hole in cross plate must be opened. Insert The breather located below hole in cross plate must be opened. Insert The breather located below hole in cross plate must be opened. Insert
slotted screw driver through hole and turn breather screw counter slotted screw driver through hole and turn breather screw counter slotted screw driver through hole and turn breather screw counter slotted screw driver through hole and turn breather screw counter
clockwise until it stops turning. Do not force screw past stopping point. clockwise until it stops turning. Do not force screw past stopping point.
BEFORE USE
Air may become trapped in the hydraulic system during transit.
To purge air:
1. Open release valve by turning handle counterclockwise.
2. Pump handle rapidly 4 full strokes. This will expel air that
may have entered hydraulic fluid passages during transit.
3. Close release valve by rotating handle clockwise and pump
handle.
4. If lift arm raises to full height, jack is ready for use. If not, repeat this
procedure or follow trouble shooting instructions provided.
INSPECTION
Visual inspection should be made before each use of the service
jack, checking for leaking hydraulic fluid and damaged, loose or
missing parts. Each jack must be inspected by a manufacturer's
repair facility immediately, if accidentally subjected to an
abnormal load or shock. Any jack which appears to be damaged
in any way, found to be badly worn, or operates abnormally
MUST BE REMOVED FROM SERVICE until necessary repairs
are made by a manufacturer's authorized repair facility. It is
recommended that an annual inspection of the jack be made
by a manufacturer's authorized repair facility and that any
defective parts, decals or warning labels be replaced with
manufacturer's specified parts.
USE ONLY ON HARD LEVEL SURFACES.
DO NOT GET UNDER A VEHICLE THAT IS ONLY SUPPORTED BY A TROLLEY/SERVICE JACK–USE VEHICLE
SUPPORT STANDS.
THIS IS A LIFTING DEVICE ONLY. DO NOT MOVE OR DOLLY THE VEHICLE WHILE ON THE JACK.
IMMEDIATELY AFTER LIFTING SUPPORT THE VEHICLE WITH APPROPRIATE MEANS.
DO NOT OVERLOAD. OVERLOADING CAN CAUSE DAMAGE TO OR FAILURE OF THE JACK.
LIFT ONLY ON AREAS OF THE VEHICLE AS SPECIFIED BY THE VEHICLE MANUFACTURER.
3202 — OPERATING MANUAL AND PARTS LIST
3202_OpMan_110905.indd 1
3202
2 Ton Extra Low Lift Service Jack
THIS OPERATING MANUAL CONTAINS IMPORTANT SAFETY INFORMATION.
READ CAREFULLY AND UNDERSTAND ALL INFORMATION BEFORE
OPERATING TOOL. SAVE THIS MANUAL FOR FUTURE USE.
A list of authorized repair facilities is availabl A list of authorized repair facilities is availabl A list of authorized repair facilities is available from the
manufacturer. manufacturer.
MAINTENANCE
IMPORTANT: When adding or replacing hydraulic fluid, always
use a quality hydraulic fluid. DO NOT use brake fluid, alcohol,
glycerine, detergent motor oil, or dirty oil as improper fluid can
cause serious internal damage to jack.
To add hydraulic fluid: With saddle fully lowered and jack
on level ground, remove breather. The hydraulic fluid
should just cover the surface of the internal cylinder visible
through the hole. Do not overfill. Replace breather. If low,
add hydraulic fluid as needed.
Maintenance and Inspection: The owner and/or user must
maintain and inspect the jack in accordance with the
manufacturer's instructions.
CENTER LOAD ON SADDLE PRIOR TO LIFTING. OFF-CENTER LOADS MAY CAUSE DAMAGE TO JACK, LOSS
OF LOAD, PROPERTY DAMAGE, PERSONAL OR FATAL INJURY.
NO ALTERATIONS TO THE JACK SHALL BE MADE.
READ, STUDY AND UNDERSTAND THE OPERATING MANUAL PACKED WITH THIS JACK BEFORE
OPERATING.
FAILURE TO HEED THESE WARNINGS MAY RESULT IN LOSS OF LOAD, DAMAGE TO JACK, AND/OR
FAILURE RESULTING IN PROPERTY DAMAGE, PERSONAL OR FATAL INJURY.
1
Breather
FOR YOUR SAFETY AND TO PREVENT INJURY:
Use Service Jack for
lifting purposes ONLY.
Always support
vehicle with
jack stands.
rev. 09/10/05
11/9/05 4:16:28 PM