Important Safety Messages - Bulldog DCH Serie Manual De Instrucciones

Before First Operation
• Purchaser/owner must ensure that
product is installed according to
these instructions. Purchaser/own-
er must not alter or modify product.
• Understand your hoist and its
instructions.
• NEvER exceed maximum rated
capacity. Refer to stamped mark-
ings or decals on product to obtain
rated capacity. If uncertain, contact
Cequent Performance Products at
1-800-632-3290 or
www.cequentgroup.com
• The hoist is rated for S3 intermittent
duty only.
Are you ready to lift?
• NEvER operate this hoist when un-
der the influence of drugs, alcohol
or medication.
• Wire rope with one or more of the
following defects shall be removed
or replaced immediately. 1) kink, 2)
distortion, 3) corrosion, 4) showing
signs of excessive wear or of having
broken wires not less than 10 pcs.
• ALWAYS remove jewelry
and wear eye protection.
• Use leather gloves or a hand
saver cable strap when handling the
wire rope.
• NEvER let hoist rope slip through
your hands.
• NEvER touch a hoist rope or
hook when someone else is at the
controls.
• NEvER touch hoist rope or hook
while under tension or under load.
• ALWAYS stand clear of hoist rope
and load and keep others away
while hoisting.
• Operator and bystanders should
NEvER position any part of body
under any portion of this product or
the load being supported.
• Do not allow children to play on
or around this product or the load
being supported.
CEQUENT

Important Safety Messages

•
clear of hoist, rope, and hook while
operating.
• The hoist is not to be used
to lift, support or otherwise trans-
port personnel.
• ALWAYS be aware of
possible hot surfaces at hoist motor,
drum or rope during or after hoist
use.
• ALWAYS ensure the operator and
bystanders are aware of the stability
of the vehicle and/or load.
Is your hoist ready to lift?
• ALWAYS inspect hoist rope, hook,
and slings before operating hoist.
Frayed, kinked or damaged hoist
rope must be replaced immediately.
Damaged components must be
replaced before operation.
• Periodically check mounting hard-
ware for proper torque and tighten
if necessary.
• ALWAYS remove any element or
obstacle that may interfere with safe
operation of the hoist.
• Wire rope can break without warn-
ing. ALWAYS keep a safe distance
from the hoist and rope while under
a load.
• ALWAYS keep wired pendant
control lead and power cord clear of
the drum, rope, and rigging. Inspect
for cracks, pinches, frayed wires or
loose connections. Damaged com-
ponents must be replaced before
operation.
• NEvER wrap hoist rope
back onto itself. Use a choker chain
or strap.
ALWAYS ensure hook latch
•
is closed and not supporting load.
• NEvER apply load to hook
tip or latch. Apply load only to the
center of hook.
• NEvER use a hook whose throat
opening has increased, or whose tip
is bent or twisted.
PERFORMANCE PRODUCTS, INC. •
™
• ALWAYS use a hook with a latch.
• NEvER hook back on rope.
Keep
• NEvER use hoist rope for towing.
• ALWAYS take time to use appropri-
During the lift
• NEvER exceed hoist or hoist rope
• Do not shock load the hoist.
• NEvER use a hoist to secure a load.
• NEvER engage or disengage the
• Prior to lift, test the function of the
• If noise or vibration occurs when
• NEvER unplug the remote control
• Keep hands and clothes away from
• When load is suspended in the air,
• NEvER (instant reverse-wind) or
• Do not connect to the wire rope with
• The operator must remain with the
• NEvER hitch a ride on the hook,
• ALWAYS remain in control. NEvER
• While working, NEvER stand under
• Be sure to lift a load vertically.
• If the hoist fails to lift a load under
• To avoid insufficient power when
After Use
• Disconnect the hand held pendant
• ALWAYS store the pendant control
F3839-00 REV C (4782) 08/15
ate rigging techniques for a hoist lift.
rated capacity.
clutch when the hoist is under load
or the drum is moving.
brake. If any malfunction of the
brake occurs, stop the operation
immediately.
running, stop the hoist immediately
and return it for repair.
when hoisting a load.
the hoist and rope.
do not weld on the load.
inch the load.
the ground of a welding machine.
hoist when it is being operated.
sling or load being moving.
neglect the hoist while actually
hoisting a load.
a lifting load or within the conveying
area.
normal conditions, stop the oper-
ation within 30 seconds otherwise
motor damage may occur.
hoisting a load. Be Sure to keep
your battery charged before, during,
and after use.
from the hoist when not in use.
in a protected, clean, dry area.
3