Product Operation - LUND 67220 Manual Original

GB

PRODUCT OPERATION

Preparing the appliance for operation
Caution! All actions described in this section must be carried out with the product unplugged. Make sure that the power cord has
been unplugged from the socket.
The product must be unpacked and all parts of the packaging completely removed. It is recommended to keep the packaging, as
it can be helpful in further transporting and storing of the product.
Check the product for damage. In the event of any damage being found, do not use the product, before the damage has been
remedied or the damaged components changed for new components, free of defects.
If the device is to be used as a mop, attach the handle by sliding the handle into the opening of the housing (II) until the latch
engages. Check correctness of the installation, a correctly fi tted handle cannot be pulled out of the housing.
After installing the handle, the hooks on the handle and housing can be used to retract the power cord for storage of the device
(XI).
Place the cloth pad on the large surface cleaning attachment so that it completely covers the bottom of the attachment (III). Pull the
string on the edge of the pad, secure with the stopper (IV) and slide the loose end of the string underneath the pad.
Put the cover (V) on the edge of the attachment with the pad.
Fix the attachment to the socket around the steam outlet. Slide the pin of the attachment into the socket until the latch button
clicks into the socket opening (VI). To disassemble the attachment, press the button and slide the attachment pin out of the socket
around the steam outlet.
The large surface cleaning attachment on the 67221 model has a UV lamp. The lamp is powered by AA batteries or rechargeable
batteries, which should be placed in the battery compartment located in the upper part of the attachment housing. Pay attention to
the correct polarity of the battery (XII). Turn the lamp on by pressing the switch in the upper part of the attachment housing. The
lamp will light up when you press the proximity button located on the bottom of the attachment housing. After applying the attach-
ment to the surface to be cleaned. If the lamp is turned off using the switch in the upper part of the attachment housing, the setting
of the lower switch is irrelevant. The operation of the UV lamp is signalled by the lighting of the lamp located in the attachment.
Warning! Do not point the UV lamp light towards the eyes and skin.
If the device is to be used as a cleaner, the holder must be removed. Press and hold the button (VII) near the housing opening
and pull the handle out.
Install the nozzle used for a particular type of operation in the socket around the steam outlet. Install the nozzle using the rigid or
fl exible extension. The extension must be installed and removed in the same manner as the attachment described above.
The nozzle is attached to the bayonet connector of the extension. Place the nozzle on the extension connector so that the pins
of the extension hit the notches in the nozzle mounting socket (VIII). Then turn the nozzle to lock it (IX). Check if the nozzle is
correctly installed and cannot be taken off by pulling it towards the steam outlet.
A cloth pad can be put over the fl at nozzle by placing it so that it completely covers the bottom of the nozzle (X).
Without the pad, the fl at nozzle can be used as a rubber puller.
Water fi lling and emptying
Caution! Make sure that the product is disconnected from the power supply before fi lling it with water or emptying. The plug of the
power cord is pulled out of the socket. The product and the water stored in it must also be cooled.
Remove the water tank cap by turning it anticlockwise. Fill the tank with water up to its nominal capacity specifi ed in the technical
data table.
A measuring cup is included with the product and it is recommended to use it, as this will minimise the risk of splashing water when
fi lling the tank. Splashed water should be thoroughly cleaned before connecting the device to the mains power supply.
After fi lling the tank, screw the tank cap in the reverse order of installation. It is forbidden to use the device with an open tank.
After use, disconnect the product from the power supply by unplugging the power cord from the socket.
Wait until the product and the water remaining in the tank have cooled down completely. Remove the tank cap, turn the device
upside down so that the inlet is facing downwards and empty the tank completely. Screw the tank cap on.
Switching the device on and off
After installing the device and fi lling the tank with water, place the device on a level, fi rm and stable surface, make sure that the
switch is in the "off " position - O, and then put the product plug into the mains socket. Move the switch to the "on" position - I, and
wait until steam escapes from the nozzle and starts working.
Warning! Make sure that body parts are not near the steam outlet. Hot steam can cause severe burns.
The device has a knob to adjust the amount of steam released from the nozzle. Turning the knob clockwise increases the intensity
of the steam jet and turning it counter-clockwise decreases the intensity.
O R I G I N A L I N S T R U C T I O N S
12