Dichiarazione Ue Di Conformità; Product Description And Intended Use; Technical Data - V2 WALLY Serie Manual

Ocultar thumbs Ver también para WALLY Serie:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 12
DICHIARAZIONE UE DI CONFORMITÀ
The manufacturer V2 S.p.A., headquarters in Corso Principi di
Piemonte 65, 12035, Racconigi (CN), Italy
Under its sole responsibility hereby declares that the products:
WALLY1-U, WALLY2-U, WALLY4-U
comply with the following directives:
2014/53/EU, ROHS-3 2015/863/EU
Racconigi, 01/06/2019
Legal representative, V2 S.p.A.
Sergio Biancheri
DISPOSAL
As for the installation operations, even at the end of this
product's life span, the dismantling operations must be
carried out by qualified experts.
This product is made up of various types of materials:
some can be recycled while others need to be disposed of.
Find out about the recycling or disposal systems envisaged by
your local regulations for this product category.
Important! – Parts of the product could contain pollutants or
hazardous substances which, if released into the environment,
could cause harmful effects to the environment itself as well as
to human health.
As indicated by the symbol opposite, throwing away this product
as domestic waste is strictly forbidden. So dispose of it as
differentiated waste, in accordance with your local regulations,
or return the product to the retailer when you purchase a new
equivalent product.
Important! – the local applicable regulations may envisage
heavy sanctions in the event of illegal disposal of this product.

PRODUCT DESCRIPTION AND INTENDED USE

This receiver is part of the WALLY series by V2 SPA.
The receivers in this series are intended for controlling the
automation type door openers, gate openers and the like, lights
and electrical circuits in general.
Any other use is improper and prohibited!
Specifications:
Operates with Royal or Personal Pass series transmitters: the
first remote control to be memorised determines the mode of
operation; Royal or Personal Pass.
Monostable, bistable or timer operating logic.
Possibility to select the contact type (N.A or N.C.) of the relay
1 through a dedicated jumper J1.
The contact of relays 2-3-4 is of N.A. type, to have an N.C.
contact. It is necessary to make changes to the hardware of
the printed circuit
Personal Pass Version:
It is possible to store up to 1008 different codes with
self-learning mode
Memory full warning: the receiver blinks 15 times
Self-learning of transmitters managed by radio
Management of the substitutive transmitter
It is possible to enable or disable the ROLLING CODE mode
Basic programming using button P1 or advanced
programming using the PROG2 (version 3.6 or newer)
programming device and WINPPCL software (version 5.0 or
newer)
WARNING: To make programming with PROG2 you need to
plug the receiver into the dedicated connector (TX).
The receiver must NOT be powered.

TECHNICAL DATA

Frequency
Power supply
Relay contacts
Temperature
Consumption
Sensibility
S/N
Size
Protection degree
RELAY CONTACTS
The contacts to the terminal board concerning the four relays are
of normally open (N.O.) type.
For a normally closed (N.C.) contact of relay 1, move the jumper
J1 to position 2 (Fig. 1).
For a normally closed contact (N.C.) of relays 2,3,4 short-circuit
point A with point B and cut the track at point C (Fig. 2) of the
relay concerned.
m
CAUTION: it is not possible to enable more than 2
relays at a time in BISTABLE or TIMER mode
- 6 -
433,92 MHz / 868,30 MHz
12 - 24 Vac / 12 - 36 Vdc
1A / 30Vdc
-20 ÷ +60°C
16 mA @ 24Vdc (stand by)
≥ -103 dBm
> 17dB @ 100dBm m=100%
132 x 26 x 74 mm
IP55

Publicidad

Tabla de contenido
loading

Tabla de contenido