Bluetooth ® Wireless Technology; To Set The Product In Operation Position; To Set The Cutting Height - Husqvarna LC 247i Manual De Usuario

Ocultar thumbs Ver también para LC 247i:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 118
®
Bluetooth
information (LC 347iVX,
LC 353iVX)
®
Bluetooth
wireless technology
The symbol for
Bluetooth
on when your mobile device is connected to the product.
(Fig. 24)

To set the product in operation position

1. Fold the handle to upright position. (Fig. 25)
2. Move the knobs up in the direction of the handle until
they stop and you hear a click. (Fig. 19)
3. Tighten the knobs fully.
WARNING:
unless the handle is fully folded up and set
in one of the applicable height positions.
To adjust the handle on page 14 .
Refer to

To set the cutting height

The cutting height can be adjusted in 6 levels.
1. Move the cutting height lever down to decrease the
cutting height.
2. Move the cutting height lever up to increase the
cutting height. (Fig. 26)
CAUTION:
too low. The blades can hit the ground if the
surface of the lawn is not level.
Battery
WARNING:
you must read and understand the safety
chapter. You must also read and understand
the operator's manual for the battery and the
battery charger.
Keep the battery and the battery charger in correct
ambient temperatures.
Operation of the bat-
tery
Charging of the bat-
tery
Battery status
The display shows the remaining battery capacity and if
there are problems with the battery. The battery capacity
is shown for 5 seconds after the product is switched off
or the battery indicator button is pressed. The warning
1696 - 002 - 03.12.2021
®
wireless technology comes
Do not operate the product
Do not set the cutting height
Before you use the battery,
Ambient temperature
5 °C - 40 °C
5 °C - 40 °C
symbol on the battery is on when an error has occurred.
Battery on page 19 .
See
(Fig. 27)
LED lights
All LEDs are lit
LED 1, LED 2, LED 3 are
lit
LED 1, LED 2 are lit
LED 1 is lit
LED 1 flashes
To charge the battery
Charge the battery before the first use. The battery is
only 30% charged when supplied to the customer.
Note:
The battery charger must be connected to the
voltage and frequency specified on the rating plate.
The battery does not charge if the battery temperature is
above 50°C. The battery charger decreases the
temperature of the battery before it starts to charge.
1. Connect one end of the power cord for the battery
charger into the socket of the battery charger.
2. Connect the other end of the power cord for the
battery charger in an grounded mains socket. The
LED on the battery charger flashes green one time.
(Fig. 28)
3. Put the battery in the battery charger. The green light
on the charger comes on when the battery is
correctly connected to the battery charger. (Fig. 29)
4. When all LEDs on the battery have come on the
battery is fully charged. Charge the battery for
maximum 24 hours.
5. To disconnect the battery charger from the mains
socket, pull the plug, not the power cord.
6. Remove the battery from the battery charger.
Battery charging status
A Husqvarna Li-ion battery can be charged or used at all
charging levels. The battery is not damaged. A fully
charged battery will not decrease its charge when the
battery is left in the charger.
LED display
LED 1 flashes
LED 1 is lit, LED 2 flashes 25%-50%
Battery status
Fully charged (75-100%)
The battery is 50%-75%
charged
The battery is 25%-50%
charged
The battery is 0%-25%
charged.
The battery is empty.
Charge the battery.
Charging status
0%-25%
15

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Lc 347ivxLc 353ivx

Tabla de contenido