Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

H-1924
FOUR DECK
PAPER CUTTER
TOOLS NEEDED
Hammer
7⁄16" Wrench x 2
FRAME ASSEMBLY
1.
Place the upright, top cross tube, assembled
upright and bottom cross tube on a table making a
rectangle. (See Figure 1)
2. Fasten bolt with washer and lock washer with nut at
each top end of the frame. (See Figure 1)
3. Fasten a foot to the bottom cross tube and the
upright using two bolts with one lock washer, one nut
and one flat washer each. (See Figure 1)
4. Repeat Step 3 by fastening the other foot to the
bottom cross tube and the assembled upright.
Tighten all nuts and bolts using two 7/16" wrenches.
5. Lay the frame on the upright side. (The side without
housing assembly on it.)
6. Insert a blade in the hole of a right arm on the
assembled upright tube. (See Figures 1 and 3)
7.
Insert the left end of the blade in the hole of the left
arm. (See Figures 2 and 3)
8. Attach the housing and dowel socket assembly to
the appropriate position on the upright with two
drive rivets. (See Figure 3)
9. Repeat steps 6-8 for the remaining stations.
PAGE 1 OF 9
1-800-295-5510
uline.com
ASSEMBLY
HOUSING AND DOWEL ASSEMBLY
NOTE: Do not open the arm on the housing
assembly prior to mounting the housing
assembly.
1.
Put both rivets through holes in housing and square
tubing as shown. (See Figure 3)
2. Hold second rivet and housing with one hand. Hit
the first rivet with a hammer until the pin is flush with
the head of the rivet.
3. Hold the housing with one hand and hit the second
rivet with a hammer until the pin is flush with the
head of the rivet.
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
0521 IH-1924

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Uline H-1924

  • Página 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. H-1924 1-800-295-5510 uline.com FOUR DECK PAPER CUTTER TOOLS NEEDED Hammer 7⁄16" Wrench x 2 ASSEMBLY FRAME ASSEMBLY HOUSING AND DOWEL ASSEMBLY Place the upright, top cross tube, assembled...
  • Página 2 ASSEMBLY CONTINUED Figure 1 Left Arm Top Cross Tube Blade Figure 2 Hex Nut Upright Right Housing and Dowel Socket Square Tube Foot Hex Bolt Bottom Cross Tube Flat Washer Assembled Upright Lock Washer PAGE 2 OF 9 0521 IH-1924...
  • Página 3 ASSEMBLY CONTINUED Figure 3 Drive Rivet Housing and Dowel Socket Head Dowel 1-800-295-5510 uline.com PAGE 3 OF 9 0521 IH-1924...
  • Página 4: Cortadora De Papel Para Cuatro Rollos

    H-1924 800-295-5510 uline.mx CORTADORA DE PAPEL PARA CUATRO ROLLOS HERRAMIENTAS NECESARIAS Martillo 2 Llaves de 7⁄16" ENSAMBLE ENSAMBLE DEL ARMAZÓN ENSAMBLE DE LA CARCASA Y EL CILINDRO 1. Coloque el marco vertical, el tubo transversal NOTA: No abra el brazo del ensamble de la...
  • Página 5: Continuación De Ensamble

    CONTINUACIÓN DE ENSAMBLE Diagrama 1 Brazo Izquierdo Tubo Transversal Superior Navaja Diagrama 2 Tuerca Hexagonal Carcasa Derecha Navaja Vertical y Orificio del Cilindro Pata de Tubo Cuadrado Perno Hexagonal Tubo Transversal Rondana Inferior Marco Vertical Plana Ensamblado Rondana de Seguridad PAGE 5 OF 9 0521 IH-1924...
  • Página 6 CONTINUACIÓN DE ENSAMBLE Diagrama 3 Remache Impulsor Carcasa y Orificio del Cilindro Cabeza Pasador Cilindro 800-295-5510 uline.mx PAGE 6 OF 9 0521 IH-1924...
  • Página 7: Outils Requis

    H-1924 1-800-295-5510 uline.ca COUPE-PAPIER À QUATRE NIVEAUX OUTILS REQUIS Marteau Clé de 7⁄16 po x 2 MONTAGE MONTAGE DU CADRE MONTAGE DE BOÎTIER ET GOUJONS Placez le montant, la traverse tubulaire supérieure, REMARQUE : N'ouvrez pas le bras sur le boîtier le montant assemblé et la traverse tubulaire avant d’installer ce dernier.
  • Página 8 MONTAGE SUITE Montant assemblé Figure 1 gauche Traverse tubulaire supérieure Lame Figure 2 Écrou hexagonal Ensemble droit de Montant boîtier et de support de goujon Pied tubulaire carré Boulon hexagonal Traverse tubulaire inférieure Rondelle Montant assemblé plate Rondelle plate de blocage PAGE 8 OF 9 0521 IH-1924...
  • Página 9 MONTAGE SUITE Figure 3 Rivet à chasser Ensemble de boîtier et de support de goujon Tête Tige Goujon 1-800-295-5510 uline.ca PAGE 9 OF 9 0521 IH-1924...

Tabla de contenido