Perles HSW4186 Instrucciones página 17

x If you use cracked or damaged grinding discs for
grinding, the grinding disc can break and cause
serious bodily injuries.
x If you remove the guard, serious bodily injuries could
be caused during grinding operation.
x If you press the spindle lock-off button during
operation, the tool can make sudden movements and
cause bodily injuries.
If power supply does not correspond to motor
voltage, the motor can be damaged and burns
can be caused due to high temperatures.
If you perform the work despite the risk of hidden
installations (water, electricity, gas pipes), which
could be damaged, you risk material damage,
electrical shock or an explosion, which can
seriously injure your health and life as well as the
health and lives of others.
INTENTIONAL USE OF THE TOOL
Preparing the tool for operation
The tool is intended for dry cutting and grinding of stone,
metals and concrete. With corresponding accessories
you can also use it for fine grinding and polishing.
Never mount saw blades on the tool.
Unplug the tool before you perform any work
on the tool.
You must always mount the guard when
working with cutting or grinding discs.
Auxiliary handle, Figure
x Fit the auxiliary handle (on the left, on the right or in
the center). Auxiliary handle must be mounted for
every work with the tool.
Turn of the guard, Figure
x The tool is equipped with a protective guard
may be adjusted to work without using any additional
accessories through approx. 360°. For turning the
guard you need to:
- Release the crank
into position B,
- Turn the guard into desired position,
- Return the crank
!
The closed side of the guard must always face the
user.
Setting the crank, Figure
x If after a long operation time the guard is not well
tightened in a certain position anymore, the guard can
turn. You must set the crank
prevent this:
- Place the tool on a flat surface,
- Release the crank
- Push the crank downwards in the direction of arrow
C so that it is removed from the nut
- Turn the crank for approx. 60° into the direction of
arrow D.
- Release the crank
in a new position.
- Do not overtighten the crank
break!
All manuals and user guides at all-guides.com
.
, which
in the direction of the arrow,
into original position A.
into a new position to
,
,
so that the nut is locked
as the screw could
Removal of the guard, Figure
For grinding with sanding paper, a wire brush or a
grinding cup you need to remove the guard
Therefore, you must:
x Loosen four screws
x Lift the guard so that it touches screw heads.
x Turn the guard so that screw heads match holes in the
guard.
x Remove the guard together with the mechanism for
turning the tool.
!
Do not loosen the screws
damage the threads in the tool's gearbox when
driving them back.
Fitting / removal or grinding and cutting accessories,
Figure
- Fit the flange
- Fit the accessory (grinding, cutting disc, etc.),
- Fit the flange nut
- Lock the spindle with the button
- Tighten the flange nut with the spanner
Remove the accessory in the reverse order.
!
The flange nut must not be overtightened.
x Before using the machine, make sure that the
accessory fitted rotates freely.
x Do not use special reducing sleeves or adapters for
fitting a grinding or a cutting disc on the tool.
Turning the main handle:
Closed handle, Figure
Open handle, Figure
The main handle
right by 90° regarding the motor gearbox. This way you
can adjust the tool to the work you perform and to
available space.
!
Turn off the switch. The handle
only if the switch is turned off.
x If the handle is closed, Figure
A in the direction of arrow E
x If the handle is open, Figure
B forward in the direction of arrow E
x Turn the handle
x The handle clamps automatically into a new position if
the crank is released.
Work with the tool
!
Read Safety Instructions and General Safety
Instructions before using the tool.
Switching on: with closed handle, Figure
with open handle, Figure
Switching on Slide the lock-off button
thus the crank switch
Push the crank switch
handle.
Switching off Release the crank switch
Locking When the tool is switched on, push the
lock-off button
Then release the crank switch
Switching off Press the crank switch
and then release it.
Soft start (HSW6236E, HSW6236EK, HSW6256E,
HSW6256EK,
HSW6238E, HSW6238EK, HSW6258E, HSW6258EK,
19
for about two turns.
completely. You can
,
,
,
/
can be turned to the left or to the
can be turned
- Move the crank
– Push the crank
into desired direction
forward and
is released.
towards the
forward and hold it.
for a short time
HSW6276CE, HSW6276CEK,
.
.
/
.