Safety Notices And Their Meaning - Hilti SFC 22/14-A Manual Del Usuario

SFC22_A_SFC14_A_P1A_01_12_2010.qxd
All manuals and user guides at all-guides.com
ORIGINAL OPERATING INSTRUCTIONS
SFC 22/14 A cordless drill / driver
It is essential that the operating instruc-
tions are read before the power tool is op-
en
erated for the first time.
Always keep these operating instructions
together with the power tool.
Ensure that the operating instructions are
with the power tool when it is given to
other persons.
Contents Page
1. General information 15
2. Description 16
3. Insert tools, accessories 18
4. Technical data 18
5. Safety instructions 19
6. Before use 22
7. Operation 24
8. Care and maintenance 25
9. Troubleshooting 26
10. Disposal 27
11. Manufacturer's warranty - tools 27
12. EC declaration of conformity 28
1. General information

1.1 Safety notices and their meaning

DANGER
Draws attention to imminent danger that could lead
to serious bodily injury or fatality.
WARNING
Draws attention to a potentially dangerous situation
that could lead to serious personal injury or fatality.
CAUTION
Draws attention to a potentially dangerous situation
that could lead to slight personal injury or damage to
the equipment or other property.
Obligation signs
Wear eye Wear a hard Wear ear Wear
protection hat protection protective
gloves
Wear
breathing
protection
Symbols
Read the Volts Direct current Rated speed
operating under no load
instructions
before use
Revolutions Drilling Return waste
per minute without material for
hammering recycling.
2. Description
2.1 Use of the product as directed
The SFC 22 A or SFC 14 A is a hand-held, battery powered combination drill for screwing and unscrewing
screws and for drilling in steel, wood and plastic.
Working on materials hazardous to the health (e.g. asbestos) is not permissible.
Do not use the battery as a power source for other unspecified appliances.
Modification of the power tool or tampering with its parts is not permissible.
To avoid the risk of injury, use only genuine Hilti accessories and insert tools.
Observe the information printed in the operating instructions concerning operation, care and maintenance.
The power tool is designed for professional use and may be operated, serviced and maintained only by trained,
authorized personnel. This personnel must be informed of any special hazards that may be encountered. The
power tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel or
when used not as directed.
The working environment may be as follows: construction site, workshop, renovation, conversion or new
construction.
2.2 Chuck
Keyless chuck
2.12.2010 16:19 Uhr
1 These numbers refer to the corresponding illustra-
tions. The illustrations can be found on the fold-out
cover pages. Keep these pages open while studying
the operating instructions.
In these operating instructions, the designation
"power tool" always refers to the SFC 22-A or SFC
14-A cordless combination drill, with battery fitted.
Parts, operating controls and indicators 1
Keyless chuck
@
Torque and drilling mode setting ring
;
Control switch (with electronic speed control)
=
Forward / reverse switch
%
2-speed gear selector switch
&
Lamp
(
Grip
)
Release buttons with additional function
+
(charge status display activation)
Charge status and fault display (Li-ion battery)
§
Belt hook (optional)
/
NOTE
Draws attention to an instruction or other useful
information.
1.2 Explanation of the pictograms and other
information
Warning signs
General Warning: Warning:
warning electricity caustic
substances
15
Location of identification data on the power tool
The type designation can be found on the type iden-
tification plate at the base of the power tool and
the serial number on the side of the casing. Make a
note of this data in your operating instructions and
always refer to it when making an enquiry to your
Hilti representative or service department.
Type:
Generation: 01
Serial no.:
16
Se