Alarm/Warning History; Automatic Restart; Maintenancemaintenance; General Instructions - Parker Hannifin Hyperchill Plus Serie Manual De Uso

4.9 Alarm/Warning history

set
ALHi
esc
set
HySP
esc set
0 1 2
esc
set
HySP
HySt
HySd
HySC
esc set set
set
esc
esc
18.06 13.46
04
Menu Code DESCRIPTION
HySP Alarm number
HySC See alarm code
See day and month of the alarm
HySd
(if the clock option is present)
ALHi See hour and minutes of the alarm
HySt
(if the clock option is present)
HyS1 b1 temperature at time of the alarm
HyS2 b2 temperature at time of the alarm
HyS3 SET conditions at time of the alarm
set
Press the button " " to enter in the menu, using the buttons "
" select the parameter " ALHi".
"and "
set
Press the button " " to enter in the menu, using the buttons "
"and " " select the parameter "HySP".
set
Press the button " " to enter in the menu, using the buttons "
"and " " select the alarm number insert (0,1,2......39) and confi rm
set
with " " (the number 0 is the last alarm started) .
set
"HySP" appears again, press " " to enter and see the date of the
English
alarm: "HySC" code (es:HP), "HySd" Date (day, month), "HySt" hour
(hour, minutes), "HyS1" "HyS2" "HyS3" sensor b1, b2 and set when the
alarm occurred.
esc
Press " " to exit.

4.10 Automatic restart

In the event of a power failure, when power is restored the chiller will
assume the On-Off status held at the moment the power was lost.
5

MaintenanceMaintenance

a) The machine is designed and built to guarantee continuous operaa)
The machine is designed and built to guarantee continuous opera-
tion; however, the life of its components depends on the mainte-
nance performed.
b) When requesting assistance or spare parts, identify the machine
(model and serial number) by reading the dataplate located on the
unit.

5.1 General instructions

!
Before performing any maintenance, make sure the power to the
HyS1
refrigerator is disconnected.
Y
set
Always use the Manufacturer's original spare parts: otherwise the
esc
Manufacturer is relieved of all liability regarding machine malfunction-
ing.
28
Y
In case of refrigerant leakage, contact qualifi ed and authorized
personnel.
Y
The Schrader valve must only be used in case of machine mal-
function: otherwise any damage caused by incorrect refrigerant charg-
ing will not be covered by the warranty.

5.2 Preventive maintenance

To guarantee lasting maximum chiller effi ciency and reliability, carry out:
Z
a) every 6 months - clean the condenser fi ns and make sure
compressor electrical absorption is within the dataplate values;
Z
b) kit for maintenance (par.7.5)
• kit for maintenance;
• service kit;
• individual spare parts.
ICEP007-024 (60Hz)
5.3 Refrigerant
Z
Charging: any damage caused by incorrect charging carried out
by unauthorized personnel will not be covered by the warranty.
Y
The equipment contains fl uorinated greenhouse gases.
At normal temperature and pressure, the R407C refrigerant is a colour-
less gas classifi ed in SAFETY GROUP A1 - EN378 (group 2 fl uid ac-
cording to Directive PED 2014/68/EU);
GWP (Global Warming Potential) = 1774.
!
In case of refrigerant leakage, air the room.
5.4 Dismantling
The refrigerant and the lubricating oil contained in the circuit must be
recovered in conformity with current local environmental regulations.
%
frame and panels steel/epoxy resin polyester
tank aluminium/copper/steel
pipes/collectors copper/aluminium/carbon steel
pipe insulation NBR rubber
compressor steel/copper/aluminium/oil
condensator steel/copper/aluminium
pump steel/cast iron/brass
fan aluminium
refrigerant R407C (HFC)
valve brass/copper
electrical cable copper/PVC
Recycling
Disposal
7 / 8