MaxPro MPBDP16 Manual Del Usuario página 10

All manuals and user guides at all-guides.com
D D rill Press MPBDP16 User Manual
Operation
1. General (Fig. 2)
To switch on the equipment, push in the green On button "I" (18); the drill starts up. To switch off, press
the red Off button "O" (19); the drill shuts down. Ensure that you do not overload the equipment. If the
sound of the motor drops in pitch during operation, it is being overloaded. Do not overload the equipment
to the point where the motor comes to a standstill.
2. Fitting tools to the drill chuck (Fig. 1)
Make sure that the power plug is removed from the socket-outlet before changing tools. Only cylindrical
tools with the stipulated maximum shaft diameter may be clamped in the drill chuck (10). Only use a tool
that is sharp and free of defects. Do not use tools whose shaft is damaged or which are deformed or
flawed in any other way. Use only accessories and attachments that are specified in the operating
instructions or have been approved by the manufacturer.
3. Using the quick-change drill chuck
Your drill is equipped with a gear-toothed drill chuck (10). In order to insert a drill bit, flip up the chip guard
(13), insert the drill bit, then tighten down the drill chuck using the supplied chuck key.
Pull out the chuck key. Ensure that the clamped tool is firmly seated.
Important. Do not leave the chuck key in the clamp hole. Doing so will cause the chuck key to be
catapulted out, which could cause injury.
4. Setting the speed (Fig. 1/8/9)
First switch the equipment off, then pull the power plug. The various spindle speeds can be set by moving
the V-belt.
Proceed as follows:
(1) Remove the screw (16) in order to open the V-belt cover (7).
(2) Slacken the tightening screw (15) and push the motor (8) in the direction of the machine head.
(3) Move the V-belt to the desired position.
(4) Refer to table (Fig. 8) for the recommended speeds.
(5) Tighten the V-belt by pushing the motor (8) away from the drill head (6). Screw the tightening screw (16)
back down again. The tension is properly set when the V-belt flexes in the middle by approx. 1cm when
pressed.
(6) Close the V-belt cover and screw down using the screw (16). The V-belt cover (7) must always be locked
tight, as the equipment is equipped with a safety switch that only allows the equipment to be turned when
the V-belt cover (7) is closed.
Important! Never let the pillar drill run when the Vbelt cover is open. Always pull power plug before
opening the cover. Never touch the V-belt when it is rotating.
4.1 Drill depth stop (Fig. 10)
The drilling spindle has a swivelling scale ring (25) for setting the drill depth. Only adjust the setting when
the equipment is at a standstill.
(1)Press the drilling spindle (11) downwards until the tip of the drill bit touches the workpiece.
(2)Slacken the clamping screw (17) and turn the scale ring (25) forwards until it stops.
(3)Turn the scale ring (25) back to the desired drill depth, then lock this setting into place using the
clamping screw (17).
Important! When setting the drill depth of a cylindrical hole you must add the length of the drill tip.
5. Setting the angle of the drill table (Fig. 7)
(1)Slacken the carriage bolt (26) under the drill table (4).
(2)Set the drill table (4) to the desired angle.
(3)Tighten down the carriage bolt (26) in order to lock the drill table (4) into this position.
6. Setting the height of the drill table (Fig. 1)
(1)Slacken the tightening screw (5).
(2)Set the drill table (4) to the desired height by pressing down or lifting up and simultaneously (gently)
pushing to the left or right.
10
GB