Drill Safety Warnings - Evolution R13 CMB Li Instrucciones Originales

www.evolutionpowertools.com
professional advice. Lead based paints should only
be removed by a professional and you should not
attempt to remove it yourself.
Once the dust has been deposited on surfaces,
hand to mouth contact can result in the ingestion
of lead. Exposure to even low levels of lead can
cause irreversible brain and nervous system
damage. The young and unborn children are
particularly vulnerable.
You are advised to consider the risks associated
with the materials you are working with and to
reduce the risk of exposure.
As some materials can produce dust that may be
hazardous to your health, we recommend the use
of an approved face mask with replaceable filters
when using this machine.
You should always:
• Work in a well-ventilated area.
• Work with approved safety equipment, such as
dust masks that are specially designed to filter
microscopic particles.
(2.8) WARNING: the operation of any power tool
can result in foreign objects being thrown towards
your eyes, which could result in severe eye
damage. Before beginning power tool operation,
always wear safety goggles or safety glasses with
side shield or a full face shield where necessary.
WARNING: Some wood and wood type
products, especially MDF (Medium Density
Fibreboard), can produce dust that may be
hazardous to your health. We recommend the
use of an approved face mask with replaceable
filters when using this machine, in addition to
using the dust extraction facility.

DRILL SAFETY WARNINGS

1) Safety instructions for all operations:
a) Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
b) Use the auxiliary handle(s). Loss of control
can cause personal injury.
c) Brace the tool properly before use. This
tool produces a high output torque and without
properly bracing the tool during operation, loss
of control may occur resulting in personal injury.
2) Safety instructions when using long drill
bits:
a) Never operate at higher speed than the
maximum speed rating of the drill bit.
b) Always start drilling at low speed and with
the bit tip in contact with the workpiece.
c) Apply pressure only in direct line with the
bit and do not apply excessive pressure
Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden wiring.
SERIAL NO. / BATCH CODE
The serial number can be found on the motor
housing of the machine. For instructions on how
to identify the batch code, please contact the
Evolution Power Tools helpline or go to:
www.evolutionpowertools.com
(4.2) ITEMS SUPPLIED
105-0001,
105-0004
Instruction
Manual
Cordless
combi drill
Belt clip
2Ah Battery
4Ah Battery
5Ah Battery
8Ah Battery
Single dock
charger
Double dock
charger
RECOMMENDED BATTERIES/CHARGERS
Description
2Ah Battery
R18BAT-Li2,
R20BAT-Li2
4Ah Battery R18BAT-Li4,
R20BAT-Li4
5Ah Battery R18BAT-Li5,
R20BAT-Li5
8Ah Battery R18BAT-Li8,
R20BAT-Li8
R18RCH-Li1- Single R18RCH-Li1,
dock charger R20RCH-Li1
R18RCH-Li2 -
R18RCH-Li2,
Double dock
R20RCH-Li2
charger
If you intend to store a battery for a period without
use then store battery at room temperature (0°C to
20°C)When storing for very long periods boost charge
the battery once per year to prevent over discharge.
The Ambient temperature range for tool and battery
use: 0°C to 40°C. The charging temperature: 5°C to
40°C.
7
105-0001A,
105-0001B,
105-0001C
105-0004A
Part No
EBAT18-Li-2
EBAT18-Li-4,
EHPB18-Li-4
EBAT18-Li-5
EHPB18-Li-8
EFC18-Li
EMC18-Li
EN