Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
gb
causing damage and accidents.
Clean the tank thoroughly when emptying it. The
mixture of different chemicals is particularly dangerous.
Incorrect cleaning may cause accidents.
Never use flammable liquids to clean the tank.
Before using the sprayer, make sure that no
components are broken or damaged. Check the
screws, the condition of the hose and the tank.
Do not use the tool when other people are nearby.
You could poison or injure other people.
If you must use mixed chemicals, mix them outside
the tank and pour them once they are mixed. Do not
use the sprayer tank to mix chemicals.
Do not use the tool with an empty tank. Damage to
the tool could occur.
Use skin, eye and respiratory protection. Chemicals
could cause poisoning and injury.
Always keep the work area well ventilated. If you use
the tool indoors you must avoid intoxication.
Always be aware of wind direction and strength. Do
not use the tool if the wind is strong. Failure to do so could
result in staining, poisoning or injury.
Avoid using the sprayer in high temperatures. High
temperatures can cause chemicals to react causing
accidents and injuries.
Do not flush chemicals or tank cleaning water down
the drain. Take environmentally harmful products to a
clean point where they can be properly processed.
Never leave the tank full or loaded after finishing the
job. If there is liquid left over after using the sprayer,
do not leave it stored in the tank of the tool. Empty
and clean all components to avoid damage to the sprayer.
BATTERIES USE AND CARE
Do not open the battery. Danger of shortcircuiting.
Protect the battery against heat, e. g., against continuous
intense sunlight, fire, water, and moisture. Danger of
explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
Use the battery only in conjunction with your STAYER
power tool. This measure alone protects the battery
against dangerous overload.
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e. g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The battery
can be damaged.
The battery is equipped with a temperature control
which allows charging only within a temperature range
of between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
first time.
The lithiumion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithiumion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted
tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be
subject to overload. When the load is too high or the
allowable battery temperature range of 0–50 °C is
exceeded, the speed is reduced. The power tool will
not run at full speed until reaching the allowable battery
temperature. position. Unintentional actuation of the On/
Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction ,
until the tool can be inserted. Insert the tool. Firmly tighten
the collar of the keyless chuck 2 by hand in rotation
direction . This automatically locks the drill chuck.
The locking is released again to remove the tool when the
collar is turned in the opposite direction.
2_FUNCTIONAL DESCRIPTION
PLACING OR FIXING THE TOOL
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
PRODUCT FEATURES
The numbering of the product features refers to the
illustration of the machine on the graphics page.
Screwdriver bit
1
Nozzle
2
Lance.
3
Tank cap
4
Lance clamp
5
Tank
6
Control lever
7
Hose
8
ON/OFF button
9
Lid / Battery compartment
10 Padded harness
ASSEMBLY
Battery charging
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time.
The lithium ion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
-
12
-
Publicidad
Tabla de contenido
