Publicidad
Idiomas disponibles
Idiomas disponibles
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) White panel clips (4) • E) #8 x 3/8" Phillips screws (4)
A
B
Metra. The World's Best Kits.
®
Jeep Renegade 2015-2020*
* Sport and Upland models with Base radio
Visit MetraOnline.com for up-to-date vehicle specific applications.
KIT FEATURES
• ISO DIN radio provision with pockets
• Painted Black to match factory finish
C
D
MetraOnline.com
E
© COPYRIGHT 2022 METRA ELECTRONICS CORPORATION
99-6532B
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Assembly
–ISO DIN radio provision with pocket . .................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Antenna Adapter:
40-EU55 Amplified antenna adapter
Wiring Harness: Visit metraonline.com for
premium options.
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Torx driver • Cutting tool
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
NOTE: Refer also to the instructions included
with the aftermarket radio.
REV. 2/2/22 INST99-6532B
Publicidad
Tabla de contenido
Manuales relacionados para Metra 99-6532B
Resumen de contenidos para Metra 99-6532B
- Página 1 Ensure that all installation connections are secure before cycling the ignition to test this product. NOTE: Refer also to the instructions included with the aftermarket radio. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 2/2/22 INST99-6532B...
-
Página 2: Dash Disassembly
DASH DISASSEMBLY 1. Using the panel removal tool, carefully unclip and remove the radio trim panel. (Figure A) 2. Remove (4) T-20 Torx screws securing the radio, disconnect the wiring, and then remove the radio. (Figure B) 3. Cut shaded area at the top of the radio Remove cavity. (Figure C) shaded area Continue to Kit Assembly (Figure A) (Figure C) (Figure B) 386-257-1187 MetraOnline.com... -
Página 3: Kit Assembly
1. A ttach the (4) white panel clips to the radio housing. (Figure A) 2. Attach the pocket to the radio brackets using (4) #8 x 3/8" Phillips screws provided with this kit. (Figure B) 3. Remove the metal “DIN” sleeve and trim ring from the aftermarket radio. 4. Attach the radio brackets to the radio using the screws supplied with the radio. (Figure C) (Figure A) (Figure B) (Figure C) 5. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/ or AXXESS. 6. Reconnect the negative battery terminal and test the aftermarket radio for proper operation. 7. Mount the radio assembly into the dash using the factory screws and slip the radio trim panel, provided with this kit, onto the radio face. 8. Reassemble the dash in the reverse order of the dash disassembly to complete the installation. REV. 2/2/22 INST99-6532B... - Página 4 Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 2/2/22 INST99-6532B...
- Página 5 NOTA: Consulte también las instrucciones incluidas con el radio de mercado secundario. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 2/2/22 INST99-6532B...
-
Página 6: Desmontaje Del Tablero
DESMONTAJE DEL TABLERO 1. Con la herramienta de extracción del panel, desenganche y retire con cuidado el panel de la moldura del radio. (Figura A) 2. Retire los (4) tornillos Torx T-20 que sujetan el radio, desconecte el cableado y luego retire el radio. (Figura B) 3. Corte el área sombreada en la parte Eliminar superior de la cavidad del radio. (Figura C) sombreado zona Continúe con el Ensamble del Kit (Figura A) (Figura C) (Figura B) 386-257-1187 MetraOnline.com... -
Página 7: Ensamble Del Kit
2. Fije la cavidad a los soportes del radio con (4) tornillos Phillips n.º 8 x 3/8” que se proporcionan con este kit. (Figura B) 3. Retire el manguito metálico “DIN” y el anillo de moldura del radio de mercado secundario. 4. Fije los soportes de la radio a la radio usando los tornillos provistos con la radio. (Figura C) (Figura A) (Figura B) (Figura C) 5. Ubique el mazo de cables de fábrica y el conector de a antena en el tablero y complete todas las conexiones necesarias a la radio. Metra recomienda usar el adaptador de acoplamiento adecuado de Metra y/o AXXESS. 6. Vuelva a conectar el terminal negativo de la batería y pruebe el radio de mercado secundario para ver si funciona correctamente. 7. Monte el conjunto de la radio en el tablero con los tornillos de fábrica y deslice el panel de la moldura de la radio, provisto con este juego, sobre la cara de la radio. 8. Vuelva a armar el tablero en orden inverso al desarmado del tablero para completar la instalación. REV. 2/2/22 INST99-6532B... - Página 8 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 2/2/22 INST99-6532B...