Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installation instructions for part 99-6532B
Jeep Renegade 2015-up
KIT FEATURES
• ISO DIN radio provision with pocket
• Painted to match factory finish
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) White panel clips • E) (4) #8 x 3/8" Phillips screws
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • XSVI-6523-NAV
Antenna Adapter: • 40-EU55 Amplified antenna adapter
METRA. The World's best kits.
99-6532B
C
D
metraonline.com
®
Dash Disassembly ................................................. 2
Kit Assembly
– ISO DIN radio provision with pocket ...................... 3
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Torx driver
E
CAUTION: Metra recommends disconnecting the negative battery
terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your
local Dealership for more information. All accessories, switches,
climate controls panels, and especially air bag indicator lights
must be connected before reconnecting the battery or cycling
the ignition. Also, do not remove the factory radio with the key
in the on position, or the vehicle running. It would be best to
remove the key from the ignition and then wait a few seconds
before removing the factory radio.
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
U.S. PATENT # D787,401
Table of Contents
Publicidad
Manuales relacionados para Metra 99-6532B
Resumen de contenidos para Metra 99-6532B
- Página 1 • A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) White panel clips • E) (4) #8 x 3/8” Phillips screws • Torx driver CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation, unless the vehicle manufacturer recommends against so.
- Página 2 99-6532B Dash Disassembly 1. Unclip and remove the trim panel surrounding the factory radio. (Figure A) 2. Remove (4) T-20 Torx Screws securing the radio. (Figure B) 3. Unplug and remove the radio. 4. Cut shaded area at the top of the Remove radio cavity.
- Página 3 1. Attach the (4) supplied white panel dash, and complete all necessary clips to the radio housing. connections to the radio. Metra (Figure A) recommends using the proper mating adapter from Metra and/or 2. Attach the pocket to the radio AXXESS.
- Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians METRA. The World’s best kits. metraonline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION...
- Página 5 INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-6532B U.S. PATENT # D787,401 Indice Jeep Renegade 2015 y mas 99-6532B Desmontaje del tablero ..........Ensamble del kit – Provisión de radio ISO DIN con cavidad ....3 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DIN con cavidad •...
- Página 6 99-6532B Desmontaje del tablero 1. Desenganche y retire el panel de moldura que rodea el radio de fábrica. (Figura A) 2. Quite los (4) tornillos Torx T-20 que sujetan el radio. (Figura B) 3. Desconecte y quite el radio. 4. Cut área sombreada en la parte Eliminar superior de la cavidad radio.
- Página 7 1. Una los (4) ganchos blancos del todas las conexiones necesarias panel suministrados a la carcasa al radio. Metra recomienda el del radio. (Figura A) uso de adaptadores adecuados de acoplamiento de Metra y/o 2.
- Página 8 INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-6532B IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones.